Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A source supplies power to the following three loads connected in parallel: (1) a lighting load drawing 10kW, (2) an induction motor drawing 10 kVA at 0.9 power factor lagging, and (3) a synchronous motor operating at 10 hp, 85% efficiency and 0.95 power factor leading (1 hp = 0.746 kW). Determine the real, reactive, and apparent power delivered by the source. Also, draw the source power triangle.
Compute the complex power S (in polar form) drawn by a certain load if it is known that (a) it draws 100 Waverage power at a lagging PF of 0.75; (b) it draws a current I = 9 + j5 A rms when connected to the voltage 120/32 V rms
Let us consider the detection of the framing bit in the T1 carrier by the receiver. Assume that the data bits in a frame assume values of 1 and 0 with equal probabilities of 0.5 and independent of each other. The framing bit alternates between 1 a..
If vid is 20-mV peak-to-peak sine wave applied in a balanced manner but superimposed on VCM= 0.5 V, what is the lowest value that VDD must have to ensure saturation mode operation for Q1 and Q2 at all times. Assume V1= 0.5 V.
A sinusoidal voltage source is zero at t = 0.2 microseconds and is "going positive" at that point, meaning that v(t') > 0 for t' = 0.21 microseconds. Furthermore, the voltage at t = 0 is -28 milliVolts and its next zero is at t = 8.2 microseconds
To familiarize yourself with the Internet Standards, search the Internet for the IETF RFC website. Using the information you find on this site, answer the following questions: Identify four types of Internet standards.
A signal source produces a 4 volt peak-to-peak sinusoid and has a source resistance of 100 ohms. We wish to drive a grounded 10 ohm load to at least 2 volts peak-to-peak with this source. The load cannot tolerate DC. Your amplifier should not burn..
If the total power amplification through the receiver stages is G_R find the output power of the receiver. If the noise power at the output is identical to the noise power at the input of the receiver, find the NF for the receiver.
Let the current int he circuit be is(t) = u(t -1) and the initial voltage in the cap be Vc(0) = -1 volts. PLOT the voltage in the cap Vc(t) for all times. Suppose we double the current is(t) = 2u(t) - u(t -1) but keep same initial condition
Build a home security system circuit using this program. The system must include 2 door sensors, 3 window sensors, 2 smoke detectors, 2 water leak sensors, and 2 motion detectors.
Three capacitors are connected in series across a 100 V battery. If the capacitances are 1 microfarad, 0.1 microfarad, and 0.01 microfarad, respectively, calculate the potential difference across each capacitor.
An unmanned X-43A scramjet test vehicle has achieved a maximum speed of Mach number 9.68 in a test flight over the Pacific Ocean. Mach number is defined as the speed of an object divided by the speed of sound.
How long will the cassette tape player operate at normal power? A walker's cassette tape player uses 4 AA batteries in series to provide 6V to the player circuit.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd