Determine the rate of mass storage inside the container now

Assignment Help Mechanical Engineering
Reference no: EM13635551

A rigid container has a total volume of 1 m, and it has one inlet pipe and two outlets. The container is half filled with water at this instant, and half filled with air. One outlet allows water to exit and the other allows air to exit. If air flows into the container at 1 atm and 20C and flows out at essentially the same state, and water flows out of the container at a rate of 1 L/min, determine the rate of mass storage inside the container. Now consider the same problem, except that heat is supplied continuously to the container, maintaining the contents at 40C.

Reference no: EM13635551

Questions Cloud

The substance comes from the stored energy of the remaining : a can of aerosol deodorant contains one pound of a scented liquid that will vaporize and spray out when the top button
During a 545 s interval a particles coordinates change from : during a 5.45 s interval a particles coordinates change from x 10.4 m y 4.95 m to x 28.8 m y -4.95 m. assuming the
If this branch of military changes the height requirements : ask a new question? assume that womens heights are normally distributed with a mean given by micro 63.9 in and a
Consider the cis trans isomers of : consider the cis trans isomers of 13-di-tert-butylcyclohexane. what unusual feature accounts for the fact that one of
Determine the rate of mass storage inside the container now : a rigid container has a total volume of 1 m and it has one inlet pipe and two outlets. the container is half filled
Consider a hypohesis test that uses a 005 significance : a sample of 27 blue jellybeans with a mean weight of 0.8580 g was taken. assume that the standard deviation is known to
Determine the velocity of the particle as a function of its : the accleration of a particle is given by a-ks2 where a is in meters per second squared k is a constant and s is in
A 100 kg truck moving at 10 ms runs into a concrete wall it : q1. a 100 kg truck moving at 10 ms runs into a concrete wall. it takes 1.0 sec for the truck to completely stop. what
If np gt5 and nqgt5 estimate pmore than 5 with n13 and p07 : if np gt5 and nqgt5 estimate pmore than 5 with n13 and p0.7 by using the normal distribution if nplt5 or nqlt5 then

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Oil with a specific gravity of 070 is used as the

oil with a specific gravity of 0.70 is used as the indicating fluid in a manometer. if the differential pressure across

  A seaplane is flying at 100 mph through air at 45 f at what

a seaplane is flying at 100 mph through air at 45 f. at what distance from the leading edge of the underside of the

  A heat loss of 20 kjkg occurs during the process neglecting

a wind turbine with a 90m-diameter rotor is rotating at 30 rpm under steady winds at an average velocity of 25 kmh.

  Saturated properties out of the evaporator

Assuming saturated properties out of the evaporator and condenser

  A 40 mm diameter hole is drilled 3 m deep into the steel

a 40 mm diameter hole is drilled 3 m deep into the steel shaft. when the two torque are applied determine a the maximum

  Assuming an axial velocity at the eye of the impeller an

a helicopter gas turbine requires an overall compressor p.r. of 101. this is to be obtained using a two-spool layout

  What are the required mass fractions of the carbon fiber

An epoxy matrix composite containing both HS (such as T-300) carbon fiber and E-glass fiber is to be formulated such that the cost/ kg is to be equal $ 8.00/ kg. It is desired to keep the total fiber volume fractionequal to 60 %. What are the requ..

  A random sample of 15 parts shows mean diameter 0742 inch

1. assuming that the diameters of 1000 brass plugs taken consecutively from a machine form a normal distribution with

  Determine the rate of heat addition and rejection for this

use constant specific heats at room temperature. round your final answers to the nearest integer. an otto cycle uses

  If the resistive force is 10 dxdt determine the

a 32 lb weight is attached to the end of a spring with spring constant k 24 lbf. if the resistive force is 10 dxdt

  What volumetric flow rate of fuel gas is required

What volumetric flow rate of fuel gas is required if there are no heat losses to the surroundings?

  1 kg of propane is contained in a piston - cylinder

1 kg of propane is contained in a piston - cylinder assembly at a constant pressure of .20 mpa heat transfer slowly to

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd