Determine the rate of entropy production in kwk a for the

Assignment Help Mechanical Engineering
Reference no: EM13639034

Work at a rate of 25 kW is done by a paddle wheel on a slurry contained within a closed, rigid tank. Heat transfer from the tank occurs at a temperature of 250°C to the surroundings that, away from the immediate vicinity of the tank, are at 27°C. Determine the rate of entropy production, in kW/K, (a) for the tank and its contents as the system, and (b) for an enlarged system including the tank and enough of the nearby surroundings for the heat transfer to occur at 27°C. Assume steady state operation in both cases.

Reference no: EM13639034

Questions Cloud

Assuming the slapping hand has a mass of 12 kg and about : if you ever slapped someone or got slapped yourself you probably remember the burning sensation. imagine you had the
Calculate the temperatures when the water rate is reduced : water specific heat 4.2 kjkg c at the rate of 120 kgmin is heated from 20 to 70 c by an oil having a specific heat of
A simple pendulum makes 120 complete oscillations in 300 : a simple pendulum makes 120 complete oscillations in 3.00 min at a location where g 9.80 ms2. find a the period of the
An airport limousine can accommodate up to four passengers : an airport limousine can accommodate up to four passengers on any one trip. the company will accept a maximum of six
Determine the rate of entropy production in kwk a for the : work at a rate of 25 kw is done by a paddle wheel on a slurry contained within a closed rigid tank. heat transfer from
A parallel-plate capacitor has an area of 540 cm2 and the : a parallel-plate capacitor has an area of 5.40 cm2 and the plates are separated by 1.20 mm. the capacitor stores a
A balloon is filled w 30 l of helium gas 1 atm what is the : a balloon is filled w 30 l. of helium gas 1 atm. what is the volume of this gas when the balloon rises to an altitude
The heat transferred over the first 6 cm of the plate is 20 : air flows at a constant velocity over a flat plate which is heated over the entire length at a fixed temperature. the
What is the probability that the number among the 25 who : suppose that 3 of the 2 million high school students who take the sat each year receive special accommodations because

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  If a 10-kg box is dropped from a height of 05 m above the

a pan of negligible mass is attached to two identical springs of stiffness k 250 nm. if a 10-kg box is dropped from a

  If the pu needs to be compressed to 25gcm3 to explode what

the atomic bomb dropped on nagasaki in 1945 used 14lbm of plutonium pu that was in a subcritical state meaning it would

  Compute the value of the corrosion potential how long do

lead experiences corrosion in an acid solution according to the following reaction pb 2h rightarrow pb2 h2 the rates

  Find out the coefficients m and b of the function you

below is measured voltage v at different time stimes 0 0.5 1 1.5 2 2.5

  The water is heated to to boiling point of water saturated

a 2.2 lb steel pot contains 2.2lb of liquid water both t59 degrees f. the water is heated to to boiling point of water

  A full revolution press has 100 rpm flywheel rotation the

a full revolution press has 100 rpm flywheel rotation. the press is equipped with tow hand trip devices mounted on the

  Now the valve is opened and the entire system is allowed to

a 2 m3 tank containing nitrogen at 25oc and 500kpa is connected through a valve to another tank containing 3kg of

  At what pressure in the test section must the tunnel

a 110 scale model of an automobile is tested in a pressurized wind tunnel. the test is to stimulate the automobile

  If m1300 nm determine the number of revolutions of b needed

an automobile wheel test rig consists og a uniform disk a of mass ma 5500 kg and radius ra1.5 m that can rotate freely

  Write down the truth table and draw a logic diagram

Prepare a 3-input, 5 bit multiplexer that fits in a 24-pin IC package. Write the truth table and draw a logic diagram and logic symbol for the multiplexer.

  Compute the x-and y-components of the force

Compute the x-and y-components of the force acting on the pinB connecting the two members of the machine subjected to the 200-N load.

  Find the heat transfer and work for each component find

a geothermal heat pump is used to provide a house with 5 kw of heating. the house is at 25degc and the ground

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd