Determine the rate of entropy change of the air

Assignment Help Mechanical Engineering
Reference no: EM13717375

Air is compressed by 10.50-kW compressor form P1 to P2. The air temperature is maintained constant at 26ºC during this process as a result of heat transfer to the surrounding medium at 10ºC. Determine the rate of entropy change of the air.

Reference no: EM13717375

Questions Cloud

Rankine power generation cycle using steam operates : A Rankine power generation cycle using steam operates at a temperature of 100°C in the condenser, a pressure of 3.0 MPa in the evaporator, and a maximum temperature of 600°C. Assuming the pump and turbine operate reversibly, plot the cycle on a T-s d..
What is the angular velocity of the disk : A solid disk rotates in the horizontal plane at an angular velocity of 0.0647 rad/s with respect to an axis perpendicular to the disk at its center. what is the angular velocity of the disk
Oil engine operating on ideal diesel cycle : An oil engine operating on the ideal diesel cycle has the overall compression ratio of 16:1, and the adiabatic expansion ratio or 8.75. The pressure and temperature at the beginning of adiabatic compression are 102.5 Kpa and 297K, respectively and th..
How much work does harold perform on the baseball : Harold the Hurler is a physics student who is renowned for his baseball pitching arm. In order to determine the amount of work he performs in throwing a baseball, How much work does Harold perform on the baseball
Determine the rate of entropy change of the air : Air is compressed by 10.50-kW compressor form P1 to P2. The air temperature is maintained constant at 26ºC during this process as a result of heat transfer to the surrounding medium at 10ºC. Determine the rate of entropy change of the air.
What is the impulse delivered to the driver by the seat belt : hen it crashes into a bridge support that does not move, a car goes from 110km/h to 0 in 1.23 m. What is the impulse delivered to the 70-kg driver by the seat belt, assuming the belt makes the driver's motion identical to the car's motion
What is the quality of the steam at the inlet : In certain instances, there are problems when the state variables that is not temperature and pressure. Consider a throttling valve. In this case, a mixture of liquid and vapor enters a valve at 3MPa and leaves at 10KPa and 500C. Assume that the valv..
Find how long does the projectile remain in the air : You throw a snowball horizontally from the roof of a building that is 56.0 m above flat ground. The initial speed of the snowball is 11.0 m/s. How long does the projectile remain in the air
The settling time does not change over range of gain values : How can you tell from a root locus if the settling time does not change over a range of gain values? What values of damping is associated when a pair of dominant poles Crosse the imaginary axis?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the temperature at the center

Fireclay brick of dimensions 0.06 m x 0.09 m x 0.20 m is removed from a kiln at 1600 K and cooled in air at 40oC with h=50 W/m2/K. What is the temperature at the center and at the corners of the brick after 50 minutes of cooling?

  Calculate the force required in direct extrusion

Calculate the force required in direct extrusion of 1100-O aluminum from a diameter of 6 in. to 2 in. Assume that the redundant work is 30% of the ideal work of deformation, and the friction work is 25% of the total work of deformation.

  Air flows on both sides of a counterflow heat exchanger

air flows on both sides of a counterflow heat exchanger operating at steady state with a mass flow rate of 1 lbs on

  The input pressure is 20 atmospheres and the output

an ideal gas flows into one end of a porous cylinder at a temperature of 400 degrees k and out the other end at a

  The bar had these original dimensions length 10000 in

during a test of a metal bar it was found that an axial tensile force of 10000 lb resulted in an elongation of 0.023

  A 005 m3 quartz tube is filled with proper proportions of

a .005 m3 quartz tube is filled with proper proportions of liquid water and water vapor at 100 kpa. it is then sealed

  Find equations for rtheta periodtheta vtheta tensiontheta

consider a conical pendulum that is a ball of mass m at the end of a string of length li moving in a horizontal circle

  Concerned about carbon content in steel

We are concerned about carbon content in steel. It has a direct effect on the yield and tensile strength of what is formed in what is called a hot rolled condition directly from the steel production facility. 1010 steel has yield strength of 180MPa, ..

  What are the temperature on the left edge of the wall the

a one dimensional wall of material kw10wmk is 50 mm thick with uniform heat generation qlsquolsquolsquo5106wm3. the

  Explain complex loading bending and compression

Complex loading (bending and compression), A steel chimney is 28m high, 1.4m external diameter, and 20mm thick. It is rigidly fixed at the base and is acted upon by a horizontal wind pressure of intensity 1.

  A double acting hydraulic cylinder rod diameter frac34

a double acting hydraulic cylinder rod diameter frac34 inches is used to compress garbage. this operation requires a

  Determine the velocity at the exit of this engines nozzle

a pure jet engine propels an aircraft at 250 ms through air at 45 kpa and -13 degc. the inlet diameter of this engine

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd