User Account

All Pages

Determine the pump power required to generate this water

Assignment Help Mechanical Engineering
Reference no: EM13624706

A cutting tool uses a nozzle that generates a high speed jet of liquid water (water temperature: 20 °C). Assume an exit velocity of 500 m/s with a jet diameter of 2 mm, at steady state.

(a) Determine the mass flow rate of liquid water through the nozzle.

(b) Determine the pump power required to generate this water jet from a steady supply of 20 °C liquid water at rest. Assume the specific enthalpy of the water at the inlet of the pump and at the exit of the nozzle to be the same.

Reference no: EM13624706

Questions Cloud

Calculate the work done and the final temperature for the : calculate the work done and the final temperature for the following processespolytropic n 1.0 1.0 kg of air t1 1470
Suppose we randomly select a sample of 64 measurements from : suppose we randomly select a sample of 64 measurements from a larger population having a mean equal to 20 and a
One kilogram of water fills a 150-l rigid container at an : one kilogram of water fills a 150-l rigid container at an initial pressure of 2 mpa. the container is then cooled to 40
What are the commpressive stresses induced by thermal : what are the commpressive stresses induced by thermal expansion in a cs pipe lined with a zirconium tube that is
Determine the pump power required to generate this water : a cutting tool uses a nozzle that generates a high speed jet of liquid water water temperature 20 degc. assume an exit
The brakes of a truck cause it to slow down by applying a : the brakes of a truck cause it to slow down by applying a retarding force of 3.0x103n to the truck over a distance of
A hollow steel shaft 6 ft long has an outer diameter of 25 : a hollow steel shaft 6 ft long has an outer diameter of 2.5 in. and an inner diameter of 1.5 in. the shaft is
A 640 g hollow ball 28 cm in diameter is suspended by a : a 640 g hollow ball 28 cm in diameter is suspended by a wire and is undergoing torsional oscillations at a frequency of
Consider a system in which r 134-a is moved through an : consider a system in which r 134-a is moved through an evaporator. the evaporator removes energy from the the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the break hp of the pump using water

Using a centrifugal pump, and a flow rate of 60 gal/min, calculate the break hp of the pump using water with a density of 62.4lbm/ft3 and do the same for a nonviscous liquid having a density of 0.85g/cm3.

  If the heating value of the natural gas fuel is 45000 kjkg

a gas turbine power plant produces a net power output of 100 mw with an overall thermal efficency of 35a if the heating

  What is discharge revised discharge pressure of compressor

What is the discharge revised discharge pressure (guage pressure) of the compressor ?  Is the assumption of change in temperature valid for calculating the discharge pressure of the compressor ?

  The steel bolt and anchor assembly is used to reinforce the

the steel bolt and anchor assembly is used to reinforce the roof of a passageway in an underground coal mine. in

  Sketch the cycle on p-v coordinates

Two kilograms of air within a piston-cylinder assembly execute a carnot power cycle with maximum and minimum temperatures of 750k and 300k, respectively.

  Calculate average velocity and mass flow rate of air

wall temperature needed for the runner to cylinder #3, such that the cylinder air inlet temperature is the same as that in cylinder #1. Runner length for cylinder #3 is 15 cm.

  A pump steadily delivers 152 kgs of water at the conditions

a pump steadily delivers 15.2 kgs of water at the conditions given below. calculate the pump power kw. there is no heat

  The only question is the strength of the block in

limestone blocks approximately 8 in. wide by 14 in. long by 6 in. high are sometimes used in constructing dry stacked

  Determine the work input and the amount of heat rejected

The cylinder of a water-cooled reciprocating compressor contains 0.05m^3 of air at 1.01bar. It is compressed isothermally to 8.0 bar. Determine the work input and the amount of heat rejected to the compressor cooling water.

  If the peak of the trajectiry is at 8 km from the launch

a projectile is launched at a with a spped u and 45 degree launch angle. if the peak of the trajectiry is at 8 km from

  Determine the tensions developed in wires

Determine the tensions developed in wires , and and the angle required for equilibrium of the 30-lb cylinder E and the 60-lb cylinder F.

  Steam at 160 bar 480degc enters a two-stage turbine

steam at 160 bar 480degc enters a two-stage turbine operating at steady sate with a volumetricnbspflow rate of 800

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd