Determine the primary current when both loads are connected

Assignment Help Electrical Engineering
Reference no: EM13261612

A 240/40 volt transformer supplies two different secondary loads. One load (a) draws a current of 12 amperes at a lagging power factor of 0.94. The other load (b) draws a current of 12 amperes at a leading power factor of 0.94. With both loads disconnected, the primary current is found to be 2 amperes at a power factor of 0.173.
Determine the primary current when both the loads are connected.

Reference no: EM13261612

Questions Cloud

What is the electrons total energy : List all the possible set of quantum numbers for a hydrogen atom with n=3. What is the electrons total energy
Explain the relationship between risk and return : Explain the relationship between risk and return. What can an investor do to reduce risk?
Determine a m-bit thermometer code for the number k : A M-bit thermometer code for the number k consists of k 1's in the least significant bit positions and M-k 0's in the more significant bit positions. A binary-to-thermometer code converter has N inputs and 2^N-1 outputs.
What limitations exist for the developed method : Is there a linear relationship between age and education, and if so, how strong is that relationship? Is it possible to predict educational level based on age? If so, what limitations exist for the developed method?
Determine the primary current when both loads are connected : A 240/40 volt transformer supplies two different secondary loads. One load (a) draws a current of 12 amperes at a lagging power factor of 0.94. The other load (b) draws a current of 12 amperes at a leading power factor of 0.94.
What is the present value of an annuity : What is the present value of an annuity of $4,000 received at the beginning of each ear for the next eight years? The first payment will be received today, and the discount rate is 9% (round to the nearest $1).
What is cyberdomes inventory balance : Cyberdome Inc. has a current ratio equal to 3, a quick ratio equal to 1.8, and total current assets of RM6 million. What is Cyberdome's inventory balance?
Find power-factor capacitor that must be placed in parallel : The lighting and motor loads of a small factory establish a 10kVA power demand at 0.7 lagging power factor on a 208V, 60 Hz supply. Determine the power-factor capacitor that must be placed in parallel
What will be the new period of the system : A performer, seated on a trapeze, is swinging back and forth with a period of 9.95 s. what will be the new period of the system

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What are the exact form of the equations

What are the exact form of the equations for the 2nd-order step response for the underdamped, critically-damped, and overdamped conditions.

  Nodal analysis solve for the current

Using nodal analysis solve for the current and supemode used to solve this circuit is located between which two nodes?

  Derive a dynamic model of the car speed v

Suppose a car of mass m moving on a straight west-east highway at velocity v(t) (positive for motion from west to east) experiences aerodynamic drag force with magnitude v(t) opposing its motion.

  Define dsss-cdma chip sequence

A DSSS-CDMA signal has a chip sequence that is 1,000 chips in length. The sequence repeats every millisecond. Define DSSS-CDMA Chip Sequence

  What is the allowable signal swing at the collector

Using a 3-V power supply, design a version of the circuit of fig 6.62 from the book. to provide a dc emitter current of 0.5 mA and to allow a +-1-V signal swing at the collector. The BJT has a nominal B=100. Use standard 5 % resistor values

  What operation is done to check if its is a negative number

In Mips when you use addi or any other commands in which you use a 16 bit value for a reg. value or address offset what operation is done to check if its is a negative number's two's complement or just a regular binary number

  Estimate the maximum gain and the frequency

a) construct the straight-line Bode plot of the gain. Is this a low-pass, high-pass, bandpass, or bandstop function b) Use the straight-line plot to estimate the maximum gain and the frequency at which it occurs.

  What would be the frequency and phase for the signal

If V = 12sin( 2 pi 1800 + 45). What would you read on a DMM Would this voltage be for an inductor or capacitor What would be the frequency and phase What does the 12 stand for Explain.

  What range of resistance values are limited by power

The maximum ratings for all resistors of this type are 250 (V) and ½ (W). What range of resistance values are limited by the maximum voltage rating of 250 (V), and what range of resistance values are limited by the maximum power of ½ (W)

  What would be the minimum allowable sampling rate

What would be the minimum allowable sampling rate for a pulse-duration modulator if it is required to handle a baseband frequency range from 50 Hz to 10 kHz

  Define addition of two numbers in ieee 754 format

Addition of two numbers in IEEE 754 format A) a=3f200000, b=be600000 B) a=3f200000, b=ff800000 C) a=01100000, b=80e00000

  Explain a certain cache has an access time

A certain cache has an access time of 2 nanoseconds and a hit percentage of 95%. If the main memory access time is 8 nanoseconds, what is the average access time for a read operation?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd