User Account

All Pages

Determine the pressure on the piston side of cylinder 1

Assignment Help Mechanical Engineering
Reference no: EM13636377

Two hydrolic cylinders are connected in series as follows. The rod side port of cylinder #1 is connected to the piston side of port of cylinder #2. The rod side port of cylinder #2 is connected directly to tank. Oil is supplied to the piston port of cylinder #1.

Cylinder #1 has a 3.25 inch diameter bore with a 1.5 inch diameter rod and a load of 10,000 lbs during extension.

cylinder #2 has a 2inch diameter bore with a 1inch diameter rod and a load of 3000 lbs during extension.

1) Determine the pressure on the piston side of cylinder #1 during extension

2) If 5gpm is suppled to the piston side of cylinder #1 determine the extension velocity of both cylinders.

Reference no: EM13636377

Questions Cloud

The traffic on the freeway is moving at a constant speed of : a car sits in an entrance ramp to a freeway waiting for a break in the traffic. the driver sees a small gap between a
How many ways there are to place three electrons into an f : how many ways there are to place three electrons into an f shell?what is the ground state term for thef3 configuration
A scuba diver created a spherical bubble with a radium of : a scuba diver created a spherical bubble with a radium of 2.0cm at a depth of 30.0m where the total pressure
As a result each object experiences an electrostatic force : two spherical objects are separated by a distance that is 1.80 x 10-3 m. the objects are initially electrically neutral
Determine the pressure on the piston side of cylinder 1 : two hydrolic cylinders are connected in series as follows. the rod side port of cylinder 1 is connected to the piston
If the initial velocity of a cannonball is 40ms and the : if the initial velocity of a cannonball is 40ms and the cannonball is launched at 72o above the horizontal how much
The wire stretches 45mm when a tensile force p is : an 18-m long steel wire of 5mm diameter is to be used in the manufacture of a presstressed concrete beam.it is observed
A plate carries a charge of -26 microc while a rod carries : a plate carries a charge of -2.6 microc while a rod carries a charge of 2.4 microc. how many electrons must be
A 05 cubic meter tank contains oxygen at 150 atm and 25oc : 1.an unknown gas has a mass of 1.36 kg and occupies a volume of 0.628cubic meters at 198 kpa and 35oc. determine the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Compare the expressions derived for parts i and ii for the

i derive an expression for the relation between heat loss and temperature difference across the inner and outer

  Determine the final temperature k and the final pressure

a rigid well insulated container is outfitted with a moveable but frictionless partition that separates two sides but

  Introductiona trebuchet is weapon developed and used europe

introductiona trebuchet is weapon developed and used europe in the 12th century. it can also be known as a counter

  Helium gas enters a nozzle at 5 ms the nozzle is not

helium gas enters a nozzle at 5 ms. the nozzle is not properly insulated and is releasing 2 kjkg of heat to the

  At what speed should the model be towed to ensure dynamic

consider a submarine cruising at 0.18 ms far below the surface in sea water at 20 degree c. a 150-scale model of the

  The extraction steam from the turbine enters the heater at

a regenerative steam power cycle has a closed feedwater heater that heats 20 kgs of water from 100degc 20 mpa to

  Find a the diameter of the ball b the ball temperature just

a 0.010 kg 10 gram round ball of solid lead at 280 k initially moves at 400 ms passing horizontally through atmospheric

  What cooling air flow rate would be required to maintain a

1 what cooling air flow rate would be required to maintain a space at 72 degrees f if it had a sensible cooling load of

  Which is probably mechanically tougher the bone or the

toughness is proportional to the amount of energy storedput in to a material or structure when a stress is applied.

  A flange is used for instrument connection for a system

a flange is used for instrument connection for a system with a design temperature of 316degc 600degf and a design

  Compute the torsional shear stress in a hallow shaft with

compute the torsional shear stress in a hallow shaft with an outside diameter of 40 mm and an inside diameter of 30 mm

  An 8 ft3 tank contains air at an initial temperature of 80f

an 8 ft3 tank contains air at an initial temperature of 80f and intial pressure of 100psi. the tank develops a small

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd