Determine the output sequence for each of the sequence

Assignment Help Electrical Engineering
Reference no: EM13275491

Design a Mealy sequential circuit which investigates an input sequence X and will produce an output Z = 1 for any input sequence ending in 0010 or 100.
Example:
X = 1 1 0 0 1 0 0 1 0 1 0 0 1 0 1
Z = 0 0 0 1 0 1 1 0 1 0 0 1 0 1 0
Notice that the circuit does not reset to the start state when an output of Z = 1 occurs. However, your circuit should have a start state and should be provided with a method for manually resetting the flip-flops to the start state. A minimum solution requires six states. Design your circuit using NAND gates, NOR gates, and three D Flip-Flops. Any solution which is minimal for your state assignment and uses 10 or fewer gates and inverters is acceptable. (Assign 000 to the start state.)
Test Procedure: First, check out your state table by starting in each state and making sure that the present output and the next state are correct for each input. Then, starting in the proper initial state, determine the output sequence for each of the following input sequences:
(1) : 0 0 1 1 0 1 0 0 1 0 1 0 1 0 0 0 1 0 0 1 0 0 1 0

Reference no: EM13275491

Questions Cloud

Role of the national labor relations board : List the major provisions of U.S. Labor laws and their underlying logic and rationale. Also, explain the role of the National Labor Relations Board (NLRB) in U.S. labor relations. Discuss how the NLRB has evolved since inception.
Find the coefficient of thermal expansion for this material : A rod is 0.5100 m long at 25C. At 225C the rod is loaded with a stress of 2 76 MPa and its length is found to be 0.5358 m, calculate the coefficient of thermal expansion for this material
Setup the masm assembler and linker : The purpose of this experiment is to setup the MASM assembler and linker. This will allow you to write assembly language source files and create executable code, such as .EXE and .COM files
Interrogation of veronese about his painting : Do you agree with the Inquisitor’s interrogation of Veronese about his painting, originally titled Last Supper? Or, do you side with Veronese?
Determine the output sequence for each of the sequence : Notice that the circuit does not reset to the start state when an output of Z = 1 occurs. However, your circuit should have a start state and should be provided with a method for manually resetting the flip-flops to the start state.
Determine how fast is the river flowing : A boat takes 3.30 hours to travel 40.0 km down a river, then 5.00 hours to return. How fast is the river flowing
Healthcare information systems and interoperability : Terminology is a major issue in development of Healthcare Information Systems (HIS) and interoperability. Dust off your nursing diagnosis text or do a query/search about NANDA, NIC, and NOC. Is this the best terminology to capture nursing's unique co..
Explain operation of common collector in npn nd pn amplifier : 1-Explain the operation of common emitter (CE) and common base (CB) in NPN amplifier 2-Explain the operation of common collector (CC) in NPN and PNP amplifiers 3- What is the relationship between the input and the output in NPN and PNP amplifiers and..
What is the expected year-end dividend : Francis Inc.'s stock has a required rate of return of 10.25%, and it sells for $57.50 per share. The dividend is expected to grow at a constant rate of 6.00% per year. What is the expected year-end dividend, D1? a. $3.25 b. $2.44 c. $2.96 d. $2.20..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Show that events a and c are independent

The lifetime of a turtle is a continuous value uniformly distributed between 50 and 150 years. Let X and Y be the lifetimes of two randomly chosen turtles, and consider the following events: A = {X

  Design an up or down counter that has an input switch x

The counter should be designed using D flip-flops and using the state equation method. (No credit will be given if the circuit is designed using the excitation table method.) Draw the final logic diagram.

  Convert the designed prototype filter to highpass filter

1. Compare a script tool such as Matlab to a block tool like Simulink and how you can use them efficiently. 2. Convert the designed prototype filter to highpass filter with cutoff frequency f_C=10,000 Hz.

  What is reflection coefficient if line is connected to load

A transmission line having a 50 ohm characteristic impedance is to drive a load of 200 ohms. 1)What is the reflection coefficient if the line is connected directly to the load 2) What is the standing wave ratio on the main line under the conditions o..

  Why does the electron gain or lose energy

The charge carried by an electron is ?1.60×10?19 C. Suppose that an electron moves through a voltage of 120V from the negative polarity to the positive polarity. How much energy is transferred Does the electron gain or lose energy

  Determine what velocity is attained by the charge

if the energy strored in the fully charged battery is used to lift the battery with 100% efficiency, what height is attained. Assume that the acceleration due to gravity is 9.8 m/s^(2) and is constant with height.

  How does combination work-band pass and band stop

A low pass filter has a cut-off frequency of 8kHz and a high pass filter has a cut-off frequency of 5kHz. These two circuits are connected back to back in cascade to form an input-output system.

  Determine e0 and write an expression for e at time t

A y polarized UPW motion in + x direction in free space has a maximum value of 20 (V/m) at a point x=1.5 (m) with the next adjacent minimum at x=2.75 (m) at time t=0 Obtain the wavelength and the frequency of the wave.

  Determine the initial x and final value x

Determine the initial x(0+) and final value x(infinity), given the following Laplace transforms X(s): X(s) = 2s2 + 5/s3 + 3s + 1

  Compute the velocity of the water jet

A hydroelectric power plant has a synchronous generator who's speed must be fixed at 180 r/min. The turbine is Pelton type with 10 m runner diameter. When the flow rate at the nozzle of the penstock is 10m^3/s, the generated electricity.

  Locate and specify an appropriate sensor

Locate and specify an appropriate sensor if it is to operate at 120 vac as an input to a PLC. Create the ladder diagram program to accomplish the specified control.

  How can be use a nand gate to make a not gate

Interface TTL logic to 120 VAC lamp. In this part of the lab, you will interface lowpower solid state electronics to the "outside world" by switching the 120 VAC lamp on and off using the AND gate from the previous experiment.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd