Determine the number of automobiles with premair catalyst

Assignment Help Mechanical Engineering
Reference no: EM13612479

Determine the number of automobiles with PremAir catalyst treated radiators needed to reduce the ozone concentration in an urban area by 10%. Assume the urban area covers 500 square miles, that there is little wind to add or remove ozone, that there is an inversion height of 2000 ft, that the air is well mixed so there is no spatial variation in concentrations. The initial concentration of ozone is 90 ppbv. Each car can treat 750,000 ft3/hr of air removing 70% of the ozone. If there are 250,000 cars operating at any given time, what percentage need to have the coating?

Reference no: EM13612479

Questions Cloud

The balance sheets at the end of each of the first two : the balance sheets at the end of each of the first two years of operations indicate the following 2006 2005 total
A gas cylinder holds 0100g of at 180 degrees cand a : a gas cylinder holds 0.100g of at 180 degrees cand a pressure of 3.50atm. the gas expands adiabatically until the
On july1 1992 prospect co sold bonds with a face value of : on july1 1992 prospect co. sold bonds with a face value of 500k and a coupon rate of 10 percent. the market interest
As you drive toward this parked car pass it and drive away : the security alarm on a parked car goes off and produces a frequency of 1110 hz. the speed of sound is 343 ms. as you
Determine the number of automobiles with premair catalyst : determine the number of automobiles with premair catalyst treated radiators needed to reduce the ozone concentration in
June 27 received a check for 1029493 from the western : june 27 received a check for 10294.93 from the western national credit card company as payment in full on credit card
Cost and quality create a work breakdown structure wbs and : create a work breakdown structure wbs and assign resources and cost by using a project management tool. as the it
At a 5 significance level 95 confidence level what is the : given a sample size of 34 with sample mean 660.3 and sample standard deviation 104.9 we perform the following
The following data relate to preston company as of december : the following data relate to preston company as of december 31 19xx building 44000 accounts receivable 24000 cash 17000

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Compute the weight percent of gold that must be added to

gold au forms a substitutional solid with silver ag. compute the weight percent of gold that must be added to silver to

  Question 1 entropya in a coal fired thermal power station

question 1 entropya in a coal fired thermal power station indicate where the exergy contained in the coal is destroyed.

  Asuming the average fuel composition and energy content

u.s. energy use was approximately 100 quads quadrillion btu in 2008. about 85 of this energy was supplied by burning

  Estimate the amount of torque needed to actuate the knee

estimate the amount of torque needed to actuate the knee near 0 deg flexion standing position based on the friction in

  Estimate the surface temperature of the pod if the air

a spherical underwater instrument pod used to make soundings and to measure conditions in the water has a diameter of

  What could be some of the strategies

How may data be managed to support a function (billing, human resources, accounting, finance, sales/marketing, training)?

  The tension t is increased in such a way that the string is

a 1-kg disk slides on a smooth horizontal table and is attached to a string that passes through a hole in the table.a

  For flow over a circular cylinder as shown below the

for flow over a circular cylinder as shown below the velocity outside of boundary layer can be estimated to beux 2 ug

  Find the amount of energy the freezer must remove from the

r-134a fills a 0.1 m3 capsule at 20oc 200 kpa. it is placed in a deep freezer where it is cooled to -10oc. the deep

  Calculate the velocity v of the collar

Calculate the velocity v of the collar as it hits the stop at B if it is elevated from rest at A by the action of the constant 40-N force in the cord. The cord is guided by the small fixed pulleys.

  The uniform work platform which has a mass per unit length

the uniform work platform which has a mass per unit length of 21 kgm is simply supported by cross rods a and b. the

  Frm a normal distribution with mean 07515 cm and standard

assuming that the diameters of 1000 brass plugs taken consecutively from a machine form a normal distribution with

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd