Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
4-pole , 500 volts shunt motor has a simplex lap winding placed in 80 solts , each cotain 30 conductors . The shunt filed resistance and the armature resistance are 250 and 0.005 ohm respectively . the flux per pole is 0.001 webers . The torque developed is 20 Nm when the motor current is 52 amp . Determine : 1- the number of armature conductors 2- the motor speed
A continuos-time system is given as a differential equation: y''(t)+2y'(t)+3y(t)=x'(t)+x(t-2) a. Compute the Transfer function H(s) of the system. b. Compute the Impulse Response h(t). c. Compute the Step Response g(t).
A single phase transformer has the following rating: 120 kVA, 2000 V/100 V, 60 Hz with 1000 primary turns. Determine (A) the maximum flux. (B) given a maximum flux density of 0.25 T, the cross-sectional area of the core.
Design a synchronous 2-bit, binary, up-counter using the following specification: The counter has five inputs ( not including the clock) and three outputs. The inputs are CLR ("Clear"), LOAD, COUNT, LB and LA.
A Gaussian random process having a mean value of 2 and a variance of 4 is passed through an ideal half-wave rectifier. a) Let Xp (t) represent the random process at the output of the half-wave rectifier
Consider a communications channel with a passband of 3 kHz to 27.4 kHz. A modem will be connected to this communications channel and the modem will operate with a signaling rate that is 0.56 the maximum allowable signaling rate for this communicat..
1. What is the purpose of core in hollow solder wire 2. What is tinning, and why is it important 3. Why is safety so important when soldering 4. Why has lead-free solder replaced lead-based solder. Be sure to properly cite any sources of information.
a. Given the random binary data sequence 0110001011, provide waveform sketches for (i) NRZ change and (ii)split phase. b.Demonstrate satisfactorily that the split phase waveform can be obtained from the NRZ waveform.
An npn differential amplifier with I = 0.5 mA, Vcc = VEE = 2.5 V, and Rc = 8 kohm utilizes BJTs with B=100 and VBE=0.7 V at Ic = 1 mA. Assuming that the bias current is obtained by a simple current source
a high power FM station of frequency 96.9 MHz has an antenna height of 1200 feet. If the signal is to be recieved 60 miles from the station, how high does the listener need to mount their anntena in this fringe area
an electric kettle is required to heat 0.6 litre of water from 10 degrees celcius to boiling point in 5 minutes,the supply voltage being 240 volts. The efficiency of the kettle is 87%. Assume the specific heat capacity of water to be 4190J/kg.K
A)what is the maximum Doppler for a vehicle speed of 160 km/hr at 900MHz. B)what is the minimum doppler(most negative for this case) C)for this range of Doppler what is the corresponding speed at 1800MHZ
Calculate( show all details, including Input versus Output voltage curve) and indicate all circuit required circuit parameter values in order to achieve both positive and negative output bounds as specified earlier. Briefly and very clearly descri..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd