Determine the molecular weight of a poly

Assignment Help Mechanical Engineering
Reference no: EM13211430

Determine the molecular weight of a poly(ethylene-propylene) with a degree of polymerization of 25,000 given that 20% of the mers (by number) are ethylene and 80% are propylenel.

Reference no: EM13211430

Questions Cloud

Determine the minimum time needed for the plate temperature : determine the minimum time needed for the plate temperature to reach 140°C.
What interest rate should be used for debt : Estimate the Departmental hurdle rates for each department. Assume that all Departments use a 45 percent debt ratio for this purpose.
Find the air exit temperature from the compressor : Air exits from the nozzle at 800m/s. find the air exit temperature from the compressor.
State the product of the reaction between chloro cyclopentyl : The product of the reaction between chloro(cyclopentyl)magnesium and pentan-2-one was treated with H2O.
Determine the molecular weight of a poly : Determine the molecular weight of a poly(ethylene-propylene) with a degree of polymerization of 25,000 given that 20% of the mers (by number) are ethylene and 80% are propylenel.
What are the design implications for the location : What are the design implications for the location and positioning of solar cells? Explain why the use of solar cells might be more appropriate in some regions of the country.
State molar mass of a volatile liquid by the dumas method : A student following the procedure of the experiment determining the molar mass of a volatile liquid by the dumas method obtaint the following data for an unknown volatile liquid
Create a design of rankine cycle : your job is to create a design of Rankine cycle that create the most possible power from this heat source . you may use any working fluid for which you can find the properties , assume the turbines 92% efficient and pumps 85%
State methyl 2-3-oxocyclohexyl acetate undergoes a reaction : Predict the product that is formed when methyl 2-(3-oxocyclohexyl)acetate undergoes

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Explain a large stationary brayton cycle gas-turbine

A large stationary Brayton cycle gas-turbine power plant delivers a power output of 100MW to an electric generator. The minimum temperature in the cycle is 300K

  Calculate the force required to hold the gate closed

the gate in the is hinged at H.the gate is 2 m wide and normal to the palne of the diagram.calculate the force required to hold the gate closed.

  Product and engineering design review

Product and Engineering Design Review

  What flow will be expected if gate valve is one-half open

The entrance is inward projecting. What flow will be expected if the gate valve is one-half open?

  Determine the latent heat of vaporization of the water vapor

How would you calculate the sensible heat, the latent heat, and determine the latent heat of vaporization of the water vapor in this air stream as the air is cooled from 170 F to 48 F?

  Define kinetics of particles -newton''s second law

Kinetics of Particles : Newton's Second Law, Determine the maximum theoretical speed that may be achieved over a distance of 50 m by a car starting from rest

  Automatic control

DOF system and Find the differential equation describing the system

  Determine the amount of steam produced per hour

Determine the amount of steam produced per hour, if the total heat loss is 10% of the heat available for steam raising - What would be the new heat transfer area if the fluids were in parallel flow

  Measurements of the load required to propagate a crack

SEM212 - Aim of this demonstration is to use measurements of the load required to propagate a crack (tear) in packaging tape to determine its fracture toughness.

  Explain compressive stress

Important information about Compressive Stress, A circular cross sectional bar with a diameter of 3.25 inches is loaded with a uniform axial compressive load of 22,750 pounds. What is the compressive stress along a cross section of the bar?

  Unidirectional reinforced composites

Calculating the mechanical properties of unidirectionally reinforced composites

  Determine the failure envelope and the non-failure region

Determine the failure envelope and the non-failure region in the sigma_y - tau_xy plane using Tsai-Hill theory for the following cases

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd