Determine the minimum theoretical operating cost

Assignment Help Mechanical Engineering
Reference no: EM13717268

When the outside temperature is -10°C, a residential heat pump must provide 3.5 x 106 kJ per day to a dwelling to maintain its temperature at 20°C. If electricity costs 8 cents per kWh, determine the minimum theoretical operating cost for each day of operation.

Reference no: EM13717268

Questions Cloud

Define and give the dimensions of thermal conductivity : Define and give the dimensions of thermal conductivity k, thermal diffusivity a,heat capacity C, heat flux q, and combined energy flux e. For the dimensions use m = mass, I = length, T = temperature, and t = time.
Executes a power cycle while operating between reservoirs : An inventor claims to have developed a device that executes a power cycle while operating between reservoirs at 500 and 300 K that has a thermal efficiency of (a) 45%, (b) 40%, (c) 35%. Evaluate the claim for each case.
The task of reengineering a process : If you were charged with the task of reengineering a process, would you be concerned with integrating only the outcomes of parallel activities that must eventually come together? Defend your response.
Water executes a carnot power cycle : One-half kilogram of water executes a Carnot power cycle. During the isothermal expansion, the water is heated until it is a saturated vapor from an initial state where the pressure is 1.5 MPa and the quality is 25%. The vapor then expands adiabatica..
Determine the minimum theoretical operating cost : When the outside temperature is -10°C, a residential heat pump must provide 3.5 x 106 kJ per day to a dwelling to maintain its temperature at 20°C. If electricity costs 8 cents per kWh, determine the minimum theoretical operating cost for each day of..
Energy equation is an expression of conservation of energy : The Energy Equation is an expression of conservation of energy. However, the terms of the equation have dimensions of length. Each of the terms is called “head”. Discuss in your own words how each of these “head terms” relate to energy, and how the o..
Determine the mass flow rate of the refrigerant : Refrigerant 134a flows at steady state through a horizontal tube having an inside diameter of .05 m. The refrigerant enters the tube with a quality of .1, temperature of 36 C, and velocity of 10 m/s. The refrigerant exits the tube at 9 bar as a satur..
Rdt and it analysis outline and annotated bibliography : With your RDT and IT Analysis Outline and Annotated Bibliography, you will demonstrate the research you have completed in your course project and receive instructor feedback. Your annotated bibliography should be annotative, as opposed to summa..
Steam generator is a type of heat exchanger : A Steam Generator is a type of heat exchanger in which hot exhaust gases (modeled as air) are used to heat saturated liquid water to produce steam. In this case hot exhaust gases enter a heat exchanger at 700 K and at a mass flow rate of 20 kg/s. Sat..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the pressure at the inlet side of the pump

Centrifugal pump draws water (r=62.4 lbm/ft^3) at a rate of 1200 gpm, and 70 degrees F (Volute Pressure =.3631 psia) from a reservoir through a 4 in diameter pipe and delivers it to a 2 in diameter discharge pipe. The pump is located 10 ft above the ..

  Assume no slipping of the cylinder and determine the

a cord is wound in the slot of cylinder a. mass b moves downward with a velocity of 6 m. assume no slipping of the

  A packed bed is composed of crushed rock with a density of

a packed bed is composed of crushed rock with a density of 175 lbmft3nbspof such anbspsize and shape that the average

  Predict the relationship between load and output voltage

Explain any anomalies - differences from theory or what you thought should happen. Is a linear approximation sufficient to describe and predict the relationship between load and output voltage?

  The engine of an automobile supplies 180 hp at 2500 rpm to

the engine of an automobile supplies 180 hp at 2500 rpm to the drive shaft. if the maximum shearing stress in the drive

  Calculate the stagnation pressure and temperature

Air flows isentropic ally at the rate of 0.5 kg/s through a supersonic convergent-divergent nozzle. At the inlet, the pressure is 680 kPa. the temperature 295 K. and the area is 6.5cm^2. If the exit area is 13 cm*2,

  The yield stress of a tension specimen machined from a 05 m

the yield stress of a tension specimen machined from a 0.5 m wide by 0.6 cm thick copper sheet is 145 mpa. the sheet is

  The uniform slender has a mass of 15 kg determine the

the uniform slender has a mass of 15 kg. determine the horizontal and vertical components of reaction on pin o and the

  Sketch the t-s diagram for the cycle

Sketch the T-s diagram for the cycle (put labels and appropriate information)

  The end of a large tubular workpart is to be faced on a nc

the end of a large tubular workpart is to be faced on a nc vertical boring mill. the part has an outside diameter 45.0

  A gas turbine power plant with regeneration delivers 80000

a gas turbine power plant with regeneration delivers 80.000 hp. the lowest pressure in the cycle in 14.7 psia and the

  Air in a cylinder is compressed reversibly and isothermally

air in a cylinder is compressed reversibly and isothermally from 95 kpa 25 o c to 290 kpa. the initial volume is 0.162

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd