Determine the minimum satisfactory total number of disks

Assignment Help Mechanical Engineering
Reference no: EM131378735

When in use, the motor and flywheel of a punch press run continuously. A compressed-air-actuated, multiple-disk clutch connects the flywheel to the countershaft each time the press is to punch or form metal. The clutch torque required is 600 N m. Alternate sintered metal and cast-iron disks are to be used. For design purposes it is decided to use 75 percent of the average value of f, and one-third of the average value of p given in Table 18.1. In addition, a safety factor of 1.20 is to be used with respect to torque capacity. Space requirements limit the disk outside diameter to 250 mm.

(a) Determine the minimum satisfactory total number of disks.

(b) Using this number of disks, determine the minimum area of compressed-air actuating surface that must be provided if air will always be available at a pressure of at least 0.40 MPa.

2407_96c5881c-5dd4-408f-840a-dac426bad1be.png

Reference no: EM131378735

Questions Cloud

Is mrs mitchell correct in given situation : She argued that since she was 17 at the time she signed the release, she was a minor and could therefore void the contract. Is Mrs. Mitchell correct? Explain.
What are three specific examples of art : What are three specific examples of art that were the most important contributions from the medieval period, and explain why you think they were influential
What is a placebo : What are the primary distinctions between case control and cohort studies - what is a measure of association?
Was sperry justified in given refusal : When Bowling found out that repair costs would almost equal the price he'd paid for the car, he left the car on Sperry's lot and asked for his money back. Sperry Ford refused to give Bowling his money. Was Sperry justified in this refusal? Explain..
Determine the minimum satisfactory total number of disks : Using this number of disks, determine the minimum area of compressed-air actuating surface that must be provided if air will always be available at a pressure of at least 0.40 MPa.
Is quality correct in given case : Quality replied that the car had been sold to an adult, so Hays could not disaffirm the contract. Is Quality correct? Explain.
Explain the influence of christianity on the visual arts : Explain the influence of Christianity on the visual arts, literature, and music of this time
Was lonchyna correct in the given case : The last time, he claimed he could void the contract, because he'd entered into it when he was a minor. Was Lonchyna correct? Explain.
What was unusual about her role for the time : What were the outstanding accomplishments of the Byzantine empire under Justinian and Theodora's rule? What was Theodora's role in the governance of Constantinople? What was unusual about her role, for the time

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd