Determine the minimum power consumption of the compressor

Assignment Help Mechanical Engineering
Reference no: EM13701738

Air flows steadily through a compressor at a rate of 1.2 kg/s. The air enters the compressor at 950 kPa and 27 degrees Celsius and exits at 2.67 MPa and 127 degrees Celsius. If heat is lost to the environment at a constant temperature of 300K, determine the minimum power consumption of the compressor in kW.

Reference no: EM13701738

Questions Cloud

Two infinitely long-vertical-concentric cylinders : A viscous fluid is contained between two infinitely long, vertical, concentric cylinders. The outer cylinder has a radius ro and rotates with an angular velocity v. The inner cylinder is fixed and has a radius ri. Make use of the Navier–Stokes equati..
Compute the net present value of each piece of equipment : Assuming a discount rate of 12%, compute the net present value of each piece of equipment. 2. A third option has surfaced for equipment purchased from an out-of-state supplier. The cost is also $560,000, but this equipment will produce even cash ..
How a court would inquire into the situation : Write a 3- to 5-page paper explaining the contract issues and how a court would inquire into the situation. Use the articles you found
Explain the impact that a diverse workforce : Identify what approaches to diversity management you would recommend to build a more diverse workforce. Explain the impact that a diverse workforce may have on your scenario organization.
Determine the minimum power consumption of the compressor : Air flows steadily through a compressor at a rate of 1.2 kg/s. The air enters the compressor at 950 kPa and 27 degrees Celsius and exits at 2.67 MPa and 127 degrees Celsius. If heat is lost to the environment at a constant temperature of 300K, determ..
What is ending inventory on a lifo basis : The most important accounting problem in dealing with merchandise inventory is the application of which of the following conventions or rules?
Write a summary of the article by reuven glick : Write a summary of the Article by Reuven Glick and Andrew K. Rose. - CONTAGION AND TRADE: WHY ARE CURRENCY CRISES REGIONAL?
What were the most critical choices faced by james milmo : What were the most critical choices faced by James Milmo early in the founding of Lynx? Do you agree with his decisions? 2. Has the founding team done a good job of structuring itself and building the Lynx organization?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A piston cylinder device contains 05 kg of water at 10mpa

a piston cylinder device contains 0.5 kg of water at 1.0mpa and 400oc. now it is cooled to 1mpa in sat-v phase.

  Complete a standard schematic diagram of the power cycle

a solar-thermal-electric power plant collects energy from sunlight focused on a high-temperature collector where solar

  The boron fibers are produced with a 125 mum diameter

a metal matrix composite mmc is made of a 2024 al alloy matrix and continuous nbspboron fibers. the boron fibers are

  Explain what will the ratio of the angle of twist

What will the ratio of the angle of twist be to that of the hollow shaft if the maximum shear stress in the material of 75 N / mm ^2 and what is the ratio of actual permissible shear stress?

  Refrigerant-134a is throttled from the saturated liquid

refrigerant-134a is throttled from the saturated liquid state at 700kpa to a pressure of 160kpa. determine the

  An ideal carnot heat engine has an efficiency of 40 if the

an ideal carnot heat engine has an efficiency of 40. if the high temperature is raised 15 what is the new efficiency

  Determine the temperature and the mass of the vapor in

piston cylinder device contains 0.06 m3 of saturated water vapor at 350 KPa pressure. Determine the temperature and the mass of the vapor in.

  Consider a system which is initially an ice cube 1 meter on

liquid water at 0degc weighs 9810 nm3 and ice at the same temperature weighs 8992 nm3. consider a system which is

  Dtermine magnitude and direction expressed by the angle

the slider p can be moved by means of the string s while the slotted arm rotates about point o. the angular position

  Determine the pressure in bars and the enthalpy in kjkg at

a piston cylinder device having an initial volume of 2 m3 initially contains steam at 10 bars and 200oc state 1. the

  What is the work required using the saturated liquid

saturated liquid water at 25 degrees c is pumped to a pressure of 5 mpa in an isothermal process. the specific work

  What is the maximum possible power per unit mass flow rate

the elevation change available at the grand coulee dam is 330 feet. what is the maximum possible power per unit mass

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd