Determine the minimum diameter of the pipe

Assignment Help Mechanical Engineering
Reference no: EM13713173

Gasoline (density = 680 kg/m^3 and kinematic viscosity = 4.29x10^-7 m^2/s) is transported at a rate of 150 L/s for a distance of 2 km. The surface roughness of the piping is 0.03 mm. If the head loss due to pipe friction is not to exceed 10 m, determine the minimum diameter of the pipe.

Reference no: EM13713173

Questions Cloud

Dry air is contained in a tank with fixed volume : Dry air is contained in a tank with fixed volume at 200 degrees Celsius and a pressure of 5 bar. Then the fluid is heated so that its temperature reaches up to 300 degrees Celsius. If the volume of the tank is 0.2 m^3, find the transferred heat and f..
Internal pressure onset of yielding based on tresca criteria : A thin-walled cylinder with open ends is subjected to constant torque of 150,000 lb-in. The cylinder is made of 2024-T3 Aluminium with a yield strength Y=50 ksi. The cylinder has a mean radius r=5in and a wall thickness of 0.05inches.
What is the length of a : Consider A= 3i+j+2k. What is the length of A, Find the unit vector of A' in the same direction as A. What is the angle between angle A and the y-axis.
What is the lasting value of big international conferences : What is the lasting value of big international conferences on sustainable development and how likely do you think it is that sustainability can be achieved solely by individuals without systemic change?
Determine the minimum diameter of the pipe : Gasoline (density = 680 kg/m^3 and kinematic viscosity = 4.29x10^-7 m^2/s) is transported at a rate of 150 L/s for a distance of 2 km. The surface roughness of the piping is 0.03 mm. If the head loss due to pipe friction is not to exceed 10 m, determ..
Structural steel with a fracture toughness : A structural steel with a fracture toughness of 60 MPa(m^1/2) has no surface crack larger than 3.5 mm in length. By how much (in %) would this largest surface crack have to grow before the system would experience fast fracture under an applied stress..
Find the required dc offset and amplification : A voltage signal ranges between -0.50 V and 1.00 V. The signal is to be sampled by an A/D converter that has an input range of 0 to 5 V. For maximum resolution, the signal is to be conditioned such that it fits the full input range of the A/D convert..
Calculate the size of the current. : a 65.2 cm long straight section of wire is located entirely inside a uniform magnetic field of |B| = 0.190 T. Calculate the size of the current.
What is the primary side current in the transformer : A single phase step up transformer is used to transform 240VRMS to 2400VRMS. The transformer is operating at its rated power of 1kW (with purely resistive load), with transformer Reqp = 5, and a Xeqp = 4j,

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  The pressure gauge at point 1 the inlet reads 25 psig and

a system carries crude oil of specific gravity 0.8. the volumetric flow rate at point 1 the inlet is 10 ft3s. branch 1

  Given a tank with 60 cm of crude oil sg086 on top of 200 cm

given a tank with 60 cm of crude oil sg0.86 on top of 200 cm of water both at 50 degrees c. barometric atomospheric

  Coefficient of friction at the tool and chip interface

A cutting tool (0.250in wide, rake angle 5 degrees) is used to machine in orthogonal mode. the depth of cut is 0.010in and the chip thickness is 0.027in. Calculate the shear angle and coefficient of friction at the tool and chip interface?

  The pressure coefficient is 10 at a and -03 at b assume

a rugged instrument used frequently for monitoring gas velocity in smoke stacks consists of two open tubes oriented to

  Diameter sphere is embedded in insulation

A 4 m diameter sphere is embedded in insulation. The sphere contains a liquid-ice mixture maintained at 0 deg C. The ambient temperature surrounding the insulation is 25 deg C.

  Determine the required diameter for the uniaxial tensile

determine the required diameter for the uniaxial tensile loaded two-force component if the failure criterion is

  Determine the current supplied if the final temperature is

a mass of 12kg of saturated refrigerant-134a vapor is contained in a frictionless piston-cylinder device at 240kpa. now

  Why do materials that have the same composition and

why do materials that have the same composition and crystal structures have the same modulus of elasticity e

  A voltage signal is produced by a transducer

A voltage signal is produced by a transducer.  The signal contains its strongest frequency component at 50 Hz (amplitude = 5.0 V), plus a weaker component at the second harmonic (100 Hz) with amplitude 2.0 V. In addition, there is noise at 60 Hz with..

  A flow of 2 kgs of saturated liquid r-134a at 200 kpa is

a flow of 2 kgs of saturated liquid r-134a at 200 kpa is mixed with 3 kgs of r-134a at 200 kpa and 10?c. the liquid and

  Determine l in cm if the manometer liquiud is mercury with

a if the pressure in the tank is 1.5 bar and atmospheric pressure is 1 bar determine l in m for water with density of

  Determine the concentration of cl in wt that must be added

high density polyethylene may be chlorinated by inducing the random substitution of chlorine atoms for hydrogen.a

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd