Determine the minimum acceptable cable cross-sectional area

Assignment Help Mechanical Engineering
Reference no: EM13608679

The required cross-sectional area of cables in a cable-stayed bridge can be estimated by keeping cable stress just at the allowable stress, while supporting the weight of the bridge deck. Say there is a pair of cables, one on each side attached every 20 m and that the total loading on the deck is 22 Mg/m, if each cable has an allowable stress of 325 MPa, and is oriented at 35 degrees from the vertical, determine the minimum acceptable cable cross-sectional area. If the cable consists of 10mmm strands, how many strands are needed?

Reference no: EM13608679

Questions Cloud

Burton companys fixed budget performance report for july : burton companys fixed budget performance report for july follows. the 675000 budgeted expenses include 634500 variable
Underfoot products uses standard costing the following : underfoot products uses standard costing. the following information about overhead was generated during may standard
From these data compute the ending inventory on each of the : some of the information found on a detail inventory card for slatkin inc. for the first month of operations is as
Bronco corporation exchanged land for equipment the land : bronco corporation exchanged land for equipment. the land had a book value of 120000 and a fair value of 150000. bronco
Determine the minimum acceptable cable cross-sectional area : the required cross-sectional area of cables in a cable-stayed bridge can be estimated by keeping cable stress just at
Included with the bank statement was an nsf cheque for 250 : the following information is for travic partsa.balance per the bank statement dated january 31 2011 is 29350.b.balance
The prescribed powers in diopters for the bifocals are 080 : a patient is going to be prescribed bifocals which will be 2.00 cm from the eye. the prescribed powers in diopters for
On march 1 2013 beldon corporation purchased land as a : on march 1 2013 beldon corporation purchased land as a factory site for 60000. an old buildding on the property was
Carpetland salespersons average 8000 per week in sales : carpetland salespersons average 8000 per week in sales steve contois the firms vice president proposes a compensation

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The acceleration of point a is defined by the relation a

the acceleration of point a is defined by the relation a -1.8 sin kt where a and t are expressed in ms2 and seconds

  Determine the final temperature and specific volume

Steam at 100 psia, 500oF is throttled to 20 psia. Changes in kinetic energy are negligible for this process. Determine the final temperature and specific volume of the steam.

  Calculate the force required to hold the gate closed

the gate in the is hinged at H.the gate is 2 m wide and normal to the palne of the diagram.calculate the force required to hold the gate closed.

  Natural gas at 70 f and standard atmospheric pressure of

natural gas at 70 f and standard atmospheric pressure of 14.7 psi is compressed isentropically to a new absolute

  The spacing between the interference fringes will increase

a laser is directed at a double-slit arrangement. if we increase the wavelength of the light which of the following

  Find out a compression ratio and inlet pressure

Also find out a compression ratio and inlet pressure to give maximum imep. engineering fundamentals of internal combustion enignes - pulkrabek.

  Determine the horizontal distance between the launching

the track for a racing event was designed so that riders jump off the slope at 30 degrees from a height of 5 ft. the

  The electric potential at a is -605 v and the electric

a moving particle encounters an external electric field that decreases its kinetic energy from 8830 ev to 7750 ev as

  Calculate the e?ciency of the furnace if the speci?c heat

Calculate the e?ciency of the furnace if the speci?c heat capacity of the water is cp = 4.2kJ/(kgK) and the zero level of enthalpy is at 0?C! (η = 79.6%)

  Estimate the skin friction drag on the aircrafts fuselage

Determine whether laminar-to-turbulent transition occurs in the boundary layer of the fuselage. If transition occurs, where does it occur - Estimate the skin friction drag on the aircraft's fuselage.

  Determine the maximun concentrated load

determine the maximun concentrated load that can be applied at the midpoint of a 3-m simple span. Neglect the weight of the beam.

  By what angle alpha should the direction of his shot trail

hockey player a carries the puck on his stick and moves in the direction shown with a speed va4 ms. in passing the puck

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd