Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Consider a long bar of square cross section (0.8 m to the side) and of thermal conductivity 2 W/m · K. Three of these sides are maintained at a uniform temperature of 300°C. The fourth side is exposed to a fluid at 100°C for which the convection heat transfer coefficient is 10W/m2 · K.
(a) Using an appropriate numerical technique with a grid spacing of 0.2 m, determine the midpoint temperature and heat transfer rate between the bar and the fluid per unit length of the bar.
(b) Reducing the grid spacing by a factor of 2, determine the midpoint temperature and heat transfer rate. Plot the corresponding temperature distribution across the surface exposed to the fluid. Also, plot the 200 and 250°C isotherms.
Every 64 cycles, the circuit outputs the average ofthe past 64 input V values, then in the next cycle begins a new calculation (in other words, its behavior repeats). During the cycles when the circuit is not outputting the average, itshould outpu..
describe with a numerical example the fundamental reason as to why live streaming video require a heavy usage of bandwidth as compared to live streaming audio. give a numerical example.
A potentiometer is wired is wired to represent a rotational range of 0-180 degree. The potentiometer is supplied with a voltage of 15 VDC. What is the output voltage at 75 degree
What is the initial acceleration of the mass if it is released and allowed to move?
A saturated npn transistor has a base to emitter applied voltage of 0.6V. The collector to emitter voltage is 0.2V. The collector current is 12mA
A) the required step-up voltage ratio for satisfactory performance. B) the voltage ratio of a standard buck-boost transformer that most closely meets the requirements of the load. C) the voltage at the load with the buck-boost transformer installed.
A certain transducer is modeled with a source Vs and series resistance Rs. The voltage at its terminals is measured with a DVM having internal resistance Ri = 100 Mega ohms and is found to be 12.5 mV; adding a 5 Mega Ohms resistance in parallel
For the circuit shown, find the input voltage Vs such that the current through R4 is 12A. R4=5 Ohms, R11 = 10 Ohms, R21 = 10 Ohms, R34 = 2 Ohms
A collimated light beam from a helium-neon laser at 632.8 nm wavelength impinges on a dielectric film of refractive index of 2.0 at an angle of 75 degrees to normal, with a polarization at 45 degrees to the plane of incidence.
Dispense requested amount using least number of bills, Write a C program for an automatic teller machine that dispenses money. The user should enter the amount desired (a multiple of 10 dollars)
the circuit has been connected for several seconds, find current in (a). in the 4.00 volts battery, (b). in the 3.00 ohm resistor, (c). in the 8.00 volts battery, (d). in the 3.00 volts battery and (e). find the charge on the capacitor?
Design a digital notch filter of the form H(z) = (1+cz-1+dz-2)/ (1+az-1+bz-2), which has a notch at fo = 60 Hz and a 3-dB width of Δf = 20 Hz. The sampling frequency fs = 8 KHz. Determine a, b, c and d.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd