Determine the maximum height h achieved the total flight

Assignment Help Mechanical Engineering
Reference no: EM13603272

An experimental fireworks shell is launched vertically from point A with an initial velocity of magnitude v0 = 140 ft/sec. In addition to the acceleration due to gravity, an internal thrusting mechanism causes a constant acceleration component of 3.0g in the direction shown for the first 3.0 seconds of flight, after which the thruster ceases to function. Determine the maximum height h achieved, the total flight time t, the net horizontal displacement x from point A, and plot the entire trajectory. Neglect any acceleration due to aerodynamics. angle is 51 dergrees instead of 60 degrees and 3.0g instead of 2g in the picture.

Reference no: EM13603272

Questions Cloud

This machine would cost 3800 polaski company has no : polaski company manufactures and sells a single product called a ret. operating at capacity the company can produce
Gorham manufacturings sales slumped badly in 2010 for the : gorham manufacturings sales slumped badly in 2010. for the first time in its history it operated at a loss. the
1 assume that adults have iq scores that are normally : 1 assume that adults have iq scores that are normally distributed with a mean of 105 and a standard deviation of 15.
A 15 kg object initially at rest is raised to a height of : a 1.5 kg object initially at rest is raised to a height of 10 m by a force of 40 n. what is the velocity of the object
Determine the maximum height h achieved the total flight : an experimental fireworks shell is launched vertically from point a with an initial velocity of magnitude v0 140
There are 10 steps leading up to the library entrance you : there are 10 steps leading up to the library entrance. you walk up the stairs taking 1 step at a time 2 steps at a time
A shell is fired at an angle of 20 degree above the : a shell is fired at an angle of 20 degree above the horizontal at a velocity of 200 ms a what is the range? b what is
Bc company uses a job order cost accounting system during : bc company uses a job order cost accounting system. during the month of april the following events occurreda purchased
In each of the following situations the sampling frame does : in each of the following situations the sampling frame does not match the population resulting in undercoverage. give

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the percent span for the old and new setpoints

In order to increase production rate, a reactor setpoint was increased from 160 psig to 190 psig. The reactor pressure transmitter was recalibrated from 0- 200 psig to 0- 300 psig. What is the percent span for the old and new setpoints?

  Design a process for the manufacture of 106 kg per year of

design a process for the manufacture of 106 kg per year of mayonnaise. the shelf life of the product is expected to be

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Determine the minimum required wire diameter

a large tower is to be supported by a series of steel wires.it is estimated that the load on each wire will be 11100N. determine the minimum required wire diameter assuming a factor of safety of 2 and a yield strength of 1030MPa.

  Determine the control resolution for this robot

The linear joint (Type L) of a certain industrial robot is actuated by a piston mechanism. The length of the joint wehn fully retracted is 600 mm and when fully extended is 1000 mm. If the robot's controller has an eight-bit storage capacity, dete..

  What is the temperature and state of the steam in the pipe

a) What is the temperature and state of the steam in the pipe? b) What is the quality of the steam in the pipe?

  Knowing that at the instant shown assembly a has a

knowing that at the instant shown assembly a has a velocity of 9in.s and an acceleration of 15 in.s2 both directed

  A cylindrical drill with radius r1 is used to bore

a cylindrical drill with radius r1 is used to bore vertically a hole through the centre of a sphere of radius r2.a find

  Explain the steam from the nozzles of a single wheel impulse

The steam from the nozzles of a single wheel impulse turbine discharges with a velocity of 600 m/s at an angle of 20 degrees. The blade wheel rotates at 3000 rev/min and the mean blade radius is 590 mm

  Steam enters a diffuser at 20 psia and 240of with a

steam enters a diffuser at 20 psia and 240of with a velocity of 900 fts and exits as saturatednbspvapor at 240of and

  Calculate athe heat lost by the oil and the cooling water

hot oil cp2.3 kjkg.c at a rate of 2.5 kgs enters an adiabatic exchanger at 180 c and leaves at 150 c. cooling water

  Estimate the theoretical fracture strength of a brittle

estimate the theoretical fracture strength of a brittle material if it is known that fracture occurs by the propagation

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd