Determine the maximum deflection of the outer spring

Assignment Help Electrical Engineering
Reference no: EM13274824

An 8-kg plunger is released from rest in the position and is stopped by two nested springs; the constant of the outer spring is k1 = 4 kN/m and the constant of the inner spring is k2 = 12 kN/m. If the plunger is released from the height
h = 600 mm, determine the maximum deflection of the outer spring

Reference no: EM13274824

Questions Cloud

What is the rate of heat flow into a system : What is the rate of heat flow into a system whose internal energy is increasing at the rate of 45 W, given that the system is doing work at the rate of 165 W
What is the minimum op amp open loop gain that is required : The output of a voltage follower is to be within .02% of the ideal value. What is the minimum op amp open loop gain that is required
Risk are present in the american economy : Several types of risk are present in the American economy. For each of the following, identify the type of risk that is present. Explain your answer.
Which of the following will cause an increase in net working : A cash dividend is declared and paid. Merchandise is sold at a profit, but the sale is on credit. Long-term bonds are retired with the proceeds of a preferred stock issue. Missing inventory is written off against retained earnings.
Determine the maximum deflection of the outer spring : An 8-kg plunger is released from rest in the position and is stopped by two nested springs; the constant of the outer spring is k1 = 4 kN/m and the constant of the inner spring is k2 = 12 kN/m. If the plunger is released from the height
Calculate the cost of electricity : Calculate the cost of electricity using a AA alkaline battery compared to the cost of electricity we use at home
Compute the standard enthalpy of formation of liquid water : Calculate the standard enthalpy of formation of liquid water (H2O) using the following thermochemical information
All sales are estimated to be bad debts : Farris estimates that it will collect 30% in the month of sale, 50% in the month after the sale, and 18% in the second month following the sale. Two percent of all sales are estimated to be bad debts. How much are Farris Co.'s budgeted cash rec..
What is the speed of sound in hydrogen : A 630-Hz sound travels through pure hydrogen. What is the speed of sound in hydrogen

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the voltage van at the low-voltage bus

3-singlephase 2 winding transformers, each rated 500 MVA, 13.8/199.2 kV, with leakage reactance Xeq = 0.10 per unit, are connected to form a three-phase bank. Winding resistances and exciting current are neglected.

  Find the voltage across the 20-ohm resistor initially

A coil of 10H inductance and 5Ω resistance is connected in parallel with a 20Ω resistor across a 100-V DC supply which is suddenly disconnected. Find The voltage across the 20Ω resistor initially and after 0.3 sec.

  Why is balancing load important for synchronous alternator

Despite the advantages to the synchronous alternator there is a downside and this has to do with keeping the load balanced on such a machine. Why is balancing the load so important to the synchronous alternator?

  Find the p-value for the test od defective boards

a six sigma black belt found that in a random sample of 140 printed circuit boards, 18 are defective. At the 5% level of significance, test that the percentage of defective boards is 10% against the alternative which is greater than 10%.

  Calculate all phase and line currents and line voltages

Assume the system shown in the Fig. is balanced, Rw = 0, Van = 208 angle 0 degree V, and positive phase sequence applies. calculate all phase and line currents, and all phase and line voltages, if Zp is equal to a) 1K ohms b) 100 + j48 ohm

  Compute the secondary and primary phasor currents of circuit

A) Draw the correct circuit to serve a 2.4kv single-phase load from a 7.2kV source. If the load is 50kva at pf=.8 lagging, compute the secondary and primary phasor currents. is this a step-up or step-down application B)Draw the correct circuit to ..

  What will be the appropriate values of quantizing level l

A binary channel with capacity 36 k bits/sec is available for PCM voic transmission. If signal is band limited to 3.2 kHz, then what will be the appropriate values of quantizing level L and the sampling frequency.

  Estimate the irradiance on the pv module facing south

The global radiation at the solar noon on a summer solstice in Albuquerque, New Mexico (latitude 35° N) is 60mw/cm^2. Assume that (a) 30 % of this irradiance is diffuse radiation and (b) the ground surrounding a PV module is non-reflecting

  Find values of external resistors for astable multivibrator

determine the values of the external resistors for a 555 timer used as an astable multivibrator with an output frequency of 2 kHz, if the external capacitor C is 3.0 mf and the duty cycle is to be approximately 75%

  Build circuit for parking deck where binary counter count up

build a circuit for a parking deck where a binary counter counts up when a car comes in and down when one leaves. There can only be a maximum of 40 cars in the parking deck before an LED turns on to notify the parking deck is full.

  Why to build and test circuits when we have simulation tools

1) Ohm's. Law is considered one of the key foundation in electronics . Why (2) Why do we have to build and test circuits when we have simulation tools

  How many quantization bits must be used to satisfy

An analog signal ranging between 0 and 1 V must be quantized. The midrange quantization errors must be no greater than 0.1V. How many quantization bits must be used to satisfy this requirement

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd