Determine the mass flow rate of condenser cooling water in

Assignment Help Mechanical Engineering
Reference no: EM13639943

Water is the working fluid in an ideal regenerative Rankine cycle with one open feedwaer heater. Superheated vapor enters the first-stage turbine at 16 MPa, 560oC, and the condenser pressure is 8 kPa. The mass flow rate of steam entering the first-stage turbine is 120 kg/s. Seam expands through the first-stage turbine to 1 MPa where some of the steam is extracted and diverted to an open feedwater heater operating at 1 MPa. The remainder expands through the second-stage turbine to the condenser pressure of 8 kPa. Saturated liquid exits the feedwater heater at 1 MPa. Determine

(a) the net power developed in kW.

(b) the rate of heat transfer to the steam passing through the boiler, in kW.

(c) the thermal efficiency

(d) the mass flow rate of condenser cooling water, in kg/s, if the cooling water undergoes a temperature increase of 18oC with negligible pressure change in passing through the condenser.

(e) Now USING EES but include in the analysis that each turbine stage and pump has an isentropic efficiency of 85%.

Reference no: EM13639943

Questions Cloud

Calculate the heat loss from the blocks five surfaces by : a hot iron block at 300 ordmc of sides 15 cm by 20 cm by 25 cm is placed on insulated horizontal surface with its 15 cm
If a charged blue board is held above the pie pan will : an aluminum pie pan is connected by a wire to a metal plate. sitting parallel to plate 1 is a second metal plate
You take 31789 g of a substance and place it into 1000 g of : you take 3.1789 g of a substance and place it into 100.0 g of benzene. the boiling point of this solution is found to
Estimate the number of gallons of gasoline consumed by the : estimate the number of gallons of gasoline consumed by the total of all automobile drivers in the united states per
Determine the mass flow rate of condenser cooling water in : water is the working fluid in an ideal regenerative rankine cycle with one open feedwaer heater. superheated vapor
Assume that the time required to download a file from the : assume that the time required to download a file from the itunes is exponentially distributed with mean equal to 4
Global positioning satellites gps can be used to determine : global positioning satellites gps can be used to determine positions with great accuracy. the system works by
Dinitrogen pentoxide decomposes in chloroform as a solvent : dinitrogen pentoxide decomposes in chloroform as a solvent to yield nitrogen dioxide and oxygen gas. the decomposition
Water at 60 of is flowing in a 6-in schedule 40 steel pipe : 1 water at 60 of is flowing in a 6-in schedule 40 steel pipe that is 100 ft long. calculate the maximum allowable

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd