Determine the mass flow rate of air going through the

Assignment Help Mechanical Engineering
Reference no: EM13614257

1) A gas turbine power plant produces a net power output of 100 MW with an overall thermal efficency of 35%

A) If the heating value of the natural gas fuel is 45000 kj/kg, determine the amount of the natural gas fuel burned in kg per day (24 hours).

B) If the air fuel ratio for the nautral gas combustion processis 17 kg air/kg fuel, determine the mass flow rate of air going through the burner in kg/s. If air is at 1 atm (101.3 kPa) and 300 K, what is the air volume flow rate in m^3/s?

Reference no: EM13614257

Questions Cloud

As you walk across a synthetic-fiber rug on a cold dry : as you walk across a synthetic-fiber rug on a cold dry winter day you pick up an excess charge of -52 .part a how many
The pulse rates for 13 adult women were as follows : the pulse rates for 13 adult women were as follows. construct a 0.90 confidence interval for the mean pulse rate. give
Present fairlyin conformity with generally : a standard auditors report contains reference toeach of the followinga. responsibilityb. generally accepted
The plates of a 33 nf parallel-plate capacitor are each : the plates of a 3.3 nf parallel-plate capacitor are each 0.27m2 in area.part a how far apart are the plates if theres
Determine the mass flow rate of air going through the : 1 a gas turbine power plant produces a net power output of 100 mw with an overall thermal efficency of 35a if the
Let z be a random variable with a standard normal : let z be a random variable with a standard normal distribution and let x be a random variable with normal distribution
The financial accounting standards board developed : the financial accounting standards board developed aconceptual framework to provide guidance in the development
If the tank is isothermal what will be the pressure in the : a 0.2 m3 tank containing helium at bar and 22 c will be used to supply 4.5 moles per minute of helium at atmospheric
Accounting standards are set in the united states in : accounting standards are set in the united states in theprivate sector. public hearings and written documents

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the internal normal force

Determine the internal normal force, shear force, and moment at point C in the simply supported beam. Point C is located just to the right of the 1500 couple moment.

  A 40 mm diameter hole is drilled 3 m deep into the steel

a 40 mm diameter hole is drilled 3 m deep into the steel shaft. when the two torque are applied determine a the maximum

  Determine the initial acceleration of the boat if it is

the 200-kg boat is powered by the fan which develops a slipstream having a diameter of 0.75 m. if the fan ejects air

  Determine the preassure at the bottom of the gate

A square 3m x 3m gate is located in the 45* sloping side of a dam. Some measurements indicate that the resultant force of the water on the gate is 500kN.(a)Determine the preassure at the bottom of the gate.(b)Show on a sketch where this force acts..

  The pressure of the gas is proportional to the balloon

spherical balloon has a diameter d1 when the pressure of the gas inside is p1 and atmospheric pressure is po. the gas

  The ball at is kicked such that 60 if it strikes the

the ball at is kicked such that 60 . if it strikes the ground at having coordinates 25 -25 determine the speed at

  Minimum weight design of a variable shape three-bar

minimum weight design of a variable shape three-bar truss.numerical solution using the matlab optimization toolbox

  Find the minimum power of the pump

Find the minimum power of the pump

  A construction crew lifts about 560 lb of material serveral

a construction crew lifts about 560 lb of material serveral times during the day from a flatbed truck to a 32 foot

  Determine the moment about c of that force

A wooden board AB, which is used as a temporary prop to support a small roof, exerts at point A of the roof a 57-lb force directed along BA. Determine the moment about C of that force.

  Determine the work input and the amount of heat rejected

The cylinder of a water-cooled reciprocating compressor contains 0.05m^3 of air at 1.01bar. It is compressed isothermally to 8.0 bar. Determine the work input and the amount of heat rejected to the compressor cooling water.

  Dtermine a the rate of shaft work transfer in kw b the

a rigid chamber contains 100 kg of water at 500 kpa 100 c. a paddle wheel stirs the water at 1000 rpm with a torque of

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd