Determine the magnitude of her acceleration

Assignment Help Mechanical Engineering
Reference no: EM131367200

Two road rally checkpoints A and B are located on the same highway and are 12 km apart. The speed limits for the first 8 km and the last 4 km of the section of highway are 100 km/h and 70 km/h, respectively. Drivers must stop at each checkpoint, and the specified time between points A and B is 8min 20 sec. Knowing that a driver accelerates and decelerates at the same constant rate, determine the magnitude of her acceleration if she travels at the speed limit as much as possible.

Reference no: EM131367200

Questions Cloud

Describe the concept of analytically driven collection : Write one to two paragraphs essay explaining the concept of "analytically driven collection." In the assigned reading for this module (Lowenthal), the author describes "analytically driven collection" as an ideal state.
How would you measure the success of a growth project : Why is top level management support needed for a growth initiative to succeed? What role can an entrepreneur play in a large or established company? How would you measure the success of a growth project? Why are growth initiatives so important to est..
Historical research have for current firefighter safety : What benefits can historical research have for current firefighter safety? What factors make fire and emergency services research difficult? Your response should be at least 200 words in length.
Establishing and maintaining positive customer relationships : 1. The author of this article states that the way to encourage customer loyalty is through excellent and thorough service. Describe the provider's responsibility for establishing and maintaining positive customer relationships.
Determine the magnitude of her acceleration : Knowing that a driver accelerates and decelerates at the same constant rate, determine the magnitude of her acceleration if she travels at the speed limit as much as possible.
Concepts of strategic management : Critically examine the concept: define the concept; identify when it was first discussed and what the arguments were for its creation; discuss how the concept then evolved by identifying the arguments for and against it over time and by noting any..
Analysis of research on death row inmates : Assignment: Analysis of Research on Death Row Inmates. Using the module readings and the Argosy University online library resources, describe the strengths and weaknesses of research on death row inmates
Neuromarketing is a controversial marketing technique : Neuromarketing is a controversial marketing technique. Research the issue and respond to the following questions in your discussion:
Statements is true about yield management systems : How should a corporation attempt to achieve synergy among functions and business units? Which of the following statements is true about yield manangement systems?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Estimate the heat flux using an appropriate free convection

Repeat the calculation for a horizontal, 7-m-diameter wire at the same excess temperature. What can you say about the general applicability of Figure 10.4 to all situations involving boiling of water at 1 atm?

  Determine the velocity ratios that can be achieved

Determine the velocity ratios that can be achieved by the gear box in terms of number of teeth in the sun wheel  and determine which component (out of the sun wheel, planet carrier and annular wheel) has to be used as the input shaft to get the req..

  Determine the steadystate amplitude of the block

For the system shown, m = 5.5 kg, k = 2300 N/m, and c = 37 N · s/m. The horizontal displacement imposed on the shaker table B is y(t) = 2.5 sin 18t mm, where the time t is measured in seconds. Determine the steadystate amplitude of the block.

  The power required to service a 400kw cooling load what

an ideal vapor compression refrigeration cycle that uses r-134a maintains a pressure in the condenser of 1000kpa and

  Determine the exit temperature by using the gas tables

Use the generalized charts to determine the exit temperature by assuming constant specific heats, and Using the gas tables.

  How long does it take the light to go from a to b

How long does it take the light to go from A to B?

  Design the risers to solidify last

Design the risers to solidify last by having its volume-to-area (V/A) ratio larg compared with the main casting and design the mold and calculate the required weight that should be used to prevent the buoyancy force from lifting the upper flask.

  Explain finding metal removal rate

Finding Metal Removal Rate In an electrochemical machining operation, the frontal working area of the electrode is 2.5in squared

  Determine the enthropy change of the system and the

a closed rigid container has a volume of 2 m3 and is filled with 4 kg of water at 200 kpa. heat is transferred from the

  Explain the effect of insulating a hot surface

Explain how heat is bst from a hot surface to the surrounding air - Explain the effect of insulating a hot surface and what is meant by the economic thickness of lagging?

  A 15-tooth pinion having a pressure angle of 25ordm and

a 15-tooth pinion having a pressure angle of 25ordm and module of 8mm is to drive an 18-tooth gear. determine for both

  For what range of exit temperatures in c can the

a large pipe carries steam as a two-phase liquid-vapor miture at 1.0 mpa. a small quantity is withdrawn through a

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd