Determine the magnitude and location of the force

Assignment Help Mechanical Engineering
Reference no: EM131314652

1. The dam shown below is 100 m wide. Determine the magnitude and location of the force on the inclined surface.


2. The float in a toilet tank is a sphere of radius R and is made of a material with ρ. An upward buoyant force F is required to shut the ballcock valve. The density of water is designated ρw. Develop an expression for x, the fraction of the float submerged, in terms of R, ρ, F, g, and ρw.

1873_Figure 04.jpg

Reference no: EM131314652

Questions Cloud

Activities for the highway project : Construction of a highway starts February 19, 2015  & completed by year end. Delay fine of $10,000 for every week of delay pass date December 31, 2015.  So 315 days (45 weeks) for the highway project  with a seven-day work schedule.
Determine your prices and r-d allocations : You use the CVP Calculator to help you develop your strategy. Your notes explaining the logic behind your decisions. SLP4 It is still January 2, 2012. Using your CVP analysis from SLP3, you run the simulation, implementing your revised four-year p..
Draw supply and demand curves for the tickets : Draw supply and demand curves for the tickets to each of the two games. (Hint: Supply is fixed. It does not change with price.) Draw one graph for each game.
Describe the discussion-political actions management : Can you be an effective manager in a large organization and avoid politics? Explain.Does politicking always cause dysfunction in an organization's operations? Explain. Support your positions by citing scholarly references.
Determine the magnitude and location of the force : An upward buoyant force F is required to shut the ballcock valve. The density of water is designated ρw. Develop an expression for x, the fraction of the float submerged, in terms of R, ρ, F, g, and ρw.
Tactical intelligence immune to influences : To what extent is tactical intelligence immune to influences from the White House, Pentagon, CENTCOM, and other headquarter's organizations over 1000 miles away? Use examples.
Ilustrate each with supply and demand curves : During 2009, incomes fell sharply for many Americans. This change would likely lead to a decrease in the prices of both normal and inferior goods.
What moment m is required to hold cube in the position shown : A cubical piece of wood with an edge L in length floats in the water. The specific gravity of the wood is 0.90.- What moment M is required to hold the cube in the position shown?
Graphically effects of both policies on market for cigarette : Are these two programs at odds with the goal of reducing cigarette consumption? As part of your answer, illustrate graphically the effects of both policies on the market for cigarettes.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A diesel engine uses 544 kg of fuel oilh of calorific

a diesel engine uses 54.4 kg of fuel oilh of calorific value 45 mjkg. the thermal efficiency of the engine is 25.

  Determine the modulus of elasticity

For a logarithmic stress strain curve and find the strength coefficient and strain hardening exponent. Determine the modulus of elasticity. Determine the toughness.

  Dtermine the moles of co that are produced at the surface

a 20-cm-long cylindrical graphite pure carbon rod is inserted into an oxidizing atmosphere at 1145 k and 1.013105 pa

  Increase heat transfer from the tube by adding fins

The outside wall surface of a 25 mm diameter metal tube (k=42 W/m*K) is maintained at 120 C. The tube is located in a room at 25 C and the convective heat transfer coefficient is 34 W/m^2*K. We'd like to increase heat transfer from the tube by adding..

  Determine the extent of heat transfer enhancement

Derive an equation to determine the extent of heat transfer enhancement due to wetting. Evaluate the enhancement for V = 10 m/s, D = 10 mm, Ts = 320 K, and Too = 300 K.

  Probable cause of discrepancy

Strains measured as the bar was pulled in tension were used to compute Young's modulus. Readings from one gauge gave a modulus much higher than those from the other gauge. What was the probable cause of this discrepancy?

  Knowing that block b has a constant velosity of 3 ins

block c starts from rest at t 0 and moves downward with a constant accelerration of 4 ins2 . knowing that block b has

  If the turbine in part a is adiabatic but only 80 efficient

a a steam turbine in a small electric power plant is designed to accept 5000kgh of steam at 60 bar and 500 c and

  Differences between scaling up and scaling out

What do you understand by ‘scalability'? Discuss the differences between ‘scaling up' and ‘scaling out' and explain when these different approaches to scalability may be used.

  A six-station automatic assembly line has an ideal cycle

a six-station automatic assembly line has an ideal cycle time of 12 sec. downtime occurs for two reasons. first

  The spacing between the interference fringes will increase

a laser is directed at a double-slit arrangement. if we increase the wavelength of the light which of the following

  A six cylinder 2-stroke diesel engine running at 120 revmin

a six cylinder 2-stroke diesel engine running at 120 revmin has a bore of 900mm and a stroke of 1300mm. the brake

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd