Determine the heat transfer for both cases

Assignment Help Mechanical Engineering
Reference no: EM13711473

Liquid propanol at 250C is burned with air at the same temperature in an atmospheric pressure combustor operating at steady conditions. Products of combustion are cooled to a temperature of 250C. Enthalpy of formation of liquid propanol = -301,000 kJ/kmol

(a) Write the balanced chemical reaction for “complete” combustion with 100% and 600% theoretical air.

 

(b) Determine the heat transfer (kJ/kg fuel) for both cases.

Reference no: EM13711473

Questions Cloud

Determine the stress and slenderness ratio : A 10 inch long cantilevered beam has a 1” by 1” square cross section. The load at the end of the beam cycles from 0 lbs to 300 lbs. determine the stress. Determine the slenderness ratio and column constant of a 38” long steel column that has a 1.5 in..
Piston-cylinder assembly in an air atmosphere : A piston-cylinder assembly in an air atmosphere of p = 1 atm (= 1.013 bar) contains 1 kg of nitrogen. The initial volume of the nitrogen is 1 m^3, and its initial pressure is 1 atm. The side of the cylinder is heated such that the heat transfer to th..
Slowly reduce the frequency to the point of synchronisation : Why do you think it is important, when using a stroboscope, to start at a very high frequency and slowly reduce the frequency to the point of synchronisation?
Gas behaviour and no change in kinetic or potential energy : A closed, rigid tank fitted with a paddle wheel contains 0.1kgof air, initially at 300 K, 0.1MPa. The paddle wheel stirs the air for 20 minutes, with the power input varying with time according to W = -10t, where W is in watts and t is time, in minut..
Determine the heat transfer for both cases : Liquid propanol at 250C is burned with air at the same temperature in an atmospheric pressure combustor operating at steady conditions. Products of combustion are cooled to a temperature of 250C. Enthalpy of formation of liquid propanol = -301,000 kJ..
Explain about research study: primary & secondary research : When conducting a Research Study, what are the advantages and disadvantages when using Face-to-Face interview as Primary Research method.
Explain the usefulness of lp : The production manager of a large Cincinnati manufacturing firm once made the statement, "I would like to use LP, but it's a technique that operates under conditions of certainty.
The stock brokerage firm : The stock brokerage firm of Blank, Leibowitz, and Weinberger has analyzed and recommended two stocks to an investors' club of college professors.
Explain this managerial decision making problem : Formulate a mathematical programming model to determine the least costly way of expanding the companies generating assets to the minimum required levels.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A container is supported by three cables that are attached

a container is supported by three cables that are attached to a ceiling as shown. determine the weight w of the

  Rigid tank contains saturated refrigerant

A 3.31 ft3 rigid tank contains saturated refrigerant-134 at 100psi. Initially, 14 percent of the volume is occupied by liquid and the rest by vapor. A valve at the top of the tank is now opened, and vapor is allowed to escape slowly from the tank. He..

  The ratio of the exit area to the inlet is 8 assuming the

air enters an adiabatic diffuser operating at steady state at 540 degrees r with a velocity of 600 fts and exits with a

  Determine for the cycle the rate of heat transfer to the

water is the working fluid in an ideal regenerative rankine cycle. superheated vapor enters the turbine at 10 mpa 5000c

  At the beginning of the compression process in an ideal

at the beginning of the compression process in an ideal otto cycle air is at 95 kpa 27 degree c and the temperature at

  A small town has a peak power requirement of 150 kw a plant

a small town has a peak power requirement of 150 kw. a plant is created using the regenerative cycle. the energy can be

  Calibrated vibrometer output indicates a velocity amplitude

the waveform from a mechanical vibration is sensed by a velocity-sensitive vibrometer. the oscilloscope trace indicates

  Compute the overall thermal resistance of a wall made up of

compute the overall thermal resistance of a wall made up of 100 mm brick 1920 kgm3 and 200 mm normal weight concrete

  If a car pasess point a with a speed of 20 ms and begins

if a car pasess point a with a speed of 20 ms and begins to increase its speed at a constatnt rate of atangential 0.5

  Calculate the following 1 wt of solids in the strained

in a process for concentrating 1000kg of freshly extracted orange juice containing 12.5 wt solids the juice is strained

  A 1 kg block of copper at 350degc is quenched in a 10 kg

a 1 kg block of copper at 350degc is quenched in a 10 kg oil bath initially at ambient temperature of 20degc.

  Neglecting heat transfer and potential energy

Steam enters a nozzle at steady state at 20 bar and 280°C, with a velocity of 80 m/s. The exit pressure and temperature are 7 bar and 180°C. Mass flow rate is 1.5 kg/s. Neglecting heat transfer and potential energy. Sketch the process on a T-v diagra..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd