Determine the heat removed from the refrigerated space

Assignment Help Mechanical Engineering
Reference no: EM13712289

Refrigerant R134a enters the compressor of a refrigerator at 0.14 MPa and -10°C at a rate of 0.12 kg/s and leaves it at 0.7 MPa and 50°C. The refrigerant is cooled in the condenser to 24°C and 0.65 MPa and it is throttled to 0.15 MPa.

Determine:

a. The heat removed from the refrigerated space

b. The power input to the compressor

c. The isentropic efficiency of the compressor and

d. The coefficient of performance of the refrigerator

e. Show the cycle on a T-s diagram

Reference no: EM13712289

Questions Cloud

A project where the company is going to close the plant : Scenario:  You have been asked to handle a project where the company is going to close the plant in your company and offer all of the workers an option of taking a buy-out severance package which is quite generous OR relocate to another state,..
Calculate the head of the crest of the model : An ogee spillway of a gravity dam is to be modeled using water.  The spillway section is 40 feet high, its crest length is 60 feet and the maximum discharge is 3,000 CFS when the head on the crest of the spillway is 5 feet.  Using a model scale of 1:..
Determine pressure of combustion gases at the turbine exit : A turbojet aircraft flies with a velocity of 900 km/h at an altitude where the air temperature and pressure are -35 degrees C and 40 kPa. Air leaves the diffuser at 50kPa with a velocity of 15 m/s, and combustion gases enter the turbine at 450 kPa an..
The legal theory of strict product liability : The legal theory of strict product liability, which has not been without controversy. Some States do not recognize this theory. Consumer advocates would argue that strict product liability is necessary to protect the small consumer from big bu..
Determine the heat removed from the refrigerated space : Refrigerant R134a enters the compressor of a refrigerator at 0.14 MPa and -10°C at a rate of 0.12 kg/s and leaves it at 0.7 MPa and 50°C. The refrigerant is cooled in the condenser to 24°C and 0.65 MPa and it is throttled to 0.15 MPa.
International law and transactions : Jackson owns a business in a foreign country that is considered "friendly" with the U.S. but which has significant political unrest. Jackson is uneasy about the situation in the country. He is concerned that his business could be the subject ..
Valveat the bottom of the container and make the liquid : A rigid tank of 0.5 m^3 is filled with saturated liquid water at 300c. so if we open a valveat the bottom of the container and make the liquid is withdrawn from the container and if the temp is still constant but the the heat transferred to the water..
Weaknesses after performing a swot analysis : From the scenarios, Erica and Chris have determined their weaknesses after performing a SWOT analysis. However, they have yet to identify opportunities for their business. Consider the industry where you currently work or an industry where you..
Determine the mechanical energy of air per unit mass : At a certain location, wind is blowing steadily at 10 m/s. Determine the mechanical energy of air per unit mass and the power generation potential of a wind turbine with 60 m diameter blades at that location. Take the air density to be 1.25 kg/m.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A nozzle receives 01 kgs steam at 1 mpa 400oc with

a nozzle receives 0.1 kgs steam at 1 mpa 400oc with negligible kinetic energy. the exit is at 500 kpa 350oc and the

  An electric motor drives a propeller inside the tank until

a closed well insulated tank contains 10 kg of air at 300 k. an electric motor drives a propeller inside the tank

  Heat transfer to the cylinder causes an isothermal

a piston-cylinder with a volume of 0.5 m3 holds 1 kg of nitrogen at a temperature of 261 k. heat transfer to the

  On the same graph plot the copper temperature history

a copper sheet of thickness 2l2mm has an initial temperature of ti118c. it is suddenly quenched in liquid water

  Determine the bulk modulus and shear modulus

A steel rod of radius 0.01m and length 2m is pulled on with a tensile force of 200,000 N, the bar stretches to a length of 2.08 m. The radius of the bar is reduced to 0.0099 m. Determine the stress, strain, Young’ modulus (E), and Poisson’s ratio (n)..

  Find the final mass of nitrogen in the tank and the final

a steel cylinder initially contains nitrogen gas at 200kpa and 25 c. the cylinder is connected to a suply line

  Assuming neglible heat transfer between the bucket and the

a one kg metal part specific heat 0.7 kjkg k initially at 1234k is quenched in a bucket containing 20 gallons of water

  Determine the pressure and temperature at the end of each

at the beginning of the compression stroke in a cold air-standard otto cycle the pressure is 0.1 mpa and the

  Calculate the heat transfer coeffcient due to natural

for this problem we will be analyzing a power amplier that is surrounded by air at 25c while the case which is

  As the container expands the pressure increases by a factor

a container with volume 213 cubic cm is heated and allowed to expand to 1.44 times the original volume. as the

  A 6-lb block is attached to a cable and to a spring

a 6-lb block is attached to a cable and to a spring vertically the cable above and the spring below. the spring

  Calculate the conduction heat loss for the following wall

Calculate the conduction heat loss for the following wall: 15ft long, 8ft tall. Calculate for 8 hr, inside temperature at 78F and the outside temperature at 3F. Wall components from outside to inside are brick; 1.2cm(1/2 in.) plywood; wood studs, 5x1..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd