Determine the greatest angular acceleration of the link

Assignment Help Mechanical Engineering
Reference no: EM13216618

The 10-kg block rests on the platform for which = 0.4. If at the instant shown link AB has an angular velocity = 2 rad/s, determine the greatest angular acceleration of the link so that the block doesn't slip.

Reference no: EM13216618

Questions Cloud

Determine the normal and shearing stresses : Two forces are applied to the pipe AB as shown. Knowing that the pipe has inner and outer diameters equal to 35 mm and 42 mm, respectively, determine the normal and shearing stresses at (a) point a, and (b) point b
Which one has the bigger moment of inertia : two spinning discs have the same angular momentum, but disk 1 has more kinetic energy than disk 2. Which one has the bigger moment of inertia - explain your reasoning?
Calculate the true stress and strain : If the rod experienced 28% uniform strain, calculated the load at the onset of necking.
Impact of watergate has contributed to this boldness : Nvestigative reporters are bolder today than they were 30 or 40 years ago. How do you think the impact of Watergate has contributed to this boldness?
Determine the greatest angular acceleration of the link : The 10-kg block rests on the platform for which = 0.4. If at the instant shown link AB has an angular velocity = 2 rad/s, determine the greatest angular acceleration of the link so that the block doesn't slip.
What is the effeciency of this engine : The heat offusion of aluminum is 3.97 10^5 J/kg; the heat of fusion of mercury is 1.18 10^4. What is the effeciency of this engine?
Role of social stratification-type of conflict : Discuss the situation reflecting on causation, role of social stratification, type of conflict (revolution, civil war, feud), and the resolution or results of the conflict.
Find the highest cycle pressure : Use cold air properties to find the highest cycle pressure, the specific energy added by combustion, and the mean effective pressure.
Decision affect the other elements of working capital : What factors may lead an organisation to change the level of inventories that it holds? How could such a decision affect the other elements of working capital?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the air velocity

the air velocity in a duct is measured by a Pitot-static probe connected to a differential pressure gage. if the air is at 13.4 psia absolute and 70 degrees C and the reading of the differential pressure gage is 0.15 psi, determine the air velocit..

  The gap between them is filled with molten polymer

Two flat, rectangular plates with a lateral dimension w*l lie parallel, one above the other, a distance h apart. The gap between them is filled with molten polymer.

  Calculate the head provided by the pump

Calculate the head provided by the pump and Calculate the brake power required if the pump efficiency is 75% (kW).

  Sketch the t-s diagram for the cycle

Sketch the T-s diagram for the cycle (put labels and appropriate information)

  Draw the block diagram of the uncontrolled seat

Draw the block diagram of the uncontrolled seat Plot the open loop displacement response of the uncontrolled seat to a step input

  What percentage of washers are discarded

25 washers have a combined mass of 1 lb. how much money is recovered per day from the sale of scrap washers?

  Locate the initial and final states on a sketches

water contained in a closed, rigid tank, initially saturated vapor at 200C, is cooled to 100C. determine the initial and final pressure, each in bar. locate the initial and final states on a sketches of the p-v and T-v digrams.

  Paint plant air house

Electricity might be used to run the fan to draw air through the system, and also to run a chiller - What is a typical COP for a commercial chiller?

  Explain horsepower and efficiency of three-phase motor

Horsepower and efficiency of three-phase motor, If a fully loaded 440V, three-phase motor draws 12.4 A at 86% power factor (pf). It's speed is 1730 rpm and its torque output to a mechanical load is 29.1 lb-ft x 1.356 = 39.5 Nm.

  Explain temperature effect on materials

Temperature Effect on Materials (i) A hollow cylinder of aluminium 1 m long with a 40 mm outside diameter is at a temperature of 20 °C. What is the change in length and circumference of the cylinder when it is cooled to â?'25 °C

  Compute the force required to punch out a rectangular

Calculate the force required to punch out a rectangular hole 100m x 50mm in a 2mm thick aluminium sheet. The ultimate strength in shear is 125 MN/m^2.

  What is the length of the slope of the ramp

Using the knon height and calculated base lenghth, what is the length of the slope of the ramp.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd