Determine the following a the gas pressure lbfin2 when the

Assignment Help Mechanical Engineering
Reference no: EM13609401

A gas is contained in a vertical piston-cylinder arrangement. The 50-lbm piston initially rests on the bottom stops. upon the addition of heat, the piston slowly rises until it touches the upper stops. The initial pressure is P1=patm=14.7 lbf/in^2. The Piston cross section is 0.05 ft^2. When the Piston is at the bottom bottom stops it rests 0.75 ft above the base of the cylinder. The top stops are located 0.3 ft above the bottom stops. Assume a quasi-equilibrium process, and neglect the volume of the stops. Determine the following: a) The gas pressure (lbf/in^2) when the piston will just lift off the bottom stops b) the work (ft.lbf) for the process.

Reference no: EM13609401

Questions Cloud

Gupta corporation has forecasted its need for external : gupta corporation has forecasted its need for external funding in the following year. it needs to raise 2m in either
How does the energy stored in a capacitor change if each : how does the energy stored in a capacitor change if each of the following happens? a the potential difference is
The following experimental data relates the observed : experiments have shown that when a clean tungsten surface is heated by laser irradiation using a focused ruby laser the
Repare a statement of cash flows using the indirect method : repare a statement of cash flows using the indirect method of reporting cash flows from operating activities. equipment
Determine the following a the gas pressure lbfin2 when the : a gas is contained in a vertical piston-cylinder arrangement. the 50-lbm piston initially rests on the bottom stops.
A rubber ball dropped from a height of 2 bounces back to a : a rubber ball dropped from a height of 2 bounces back to a height of 1. draw the balls position and velocity graphs
Assuming n eyx beta0- beta1x the least squares estimates : the relationship assumed linear between yeild of bourbon y and aging time x was studied by observing yields y-initial
On the basis of the following data for branch co for the : on the basis of the following data for branch co. for the year ended december 31 2011 and the preceding year prepare a
A farmer grows two crops lettuce and beans the farmer uses : a farmer grows two crops lettuce and beans. the farmer uses three inputs labor seed and fertilizer. the past prices and

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A sealed rigid container of volume 6 m3 contains water in

a sealed rigid container of volume .6 m3 contains water in the form of saturated vapor at 550 kpa. energy in the form

  If the pressure 3 p is doubled how will this affect the

an ideal gas of mass 2 kg is contained within a rigid cylinder and undergoes a cycle which consists of three separate

  What is the approximate magnetic field b on the axis

A solenoid 2.8 m long has a radius of 0.85 cm and 660 turns. It carries a current I of 2.5 A. What is the approximate magnetic field B on the axis of the solenoid?

  Determine the peak runoff

Determine the peak runoff from 500 ft of pavement(32ft wide) that drains toward a gutter(for 10 years freq. storm), the pavement slope is .0005, n=.016 and c=.9

  Determine the tension in the cable

the frame ACD is supported by a ball-and-socket joint at A and D and by a cable which passes through a ring at B and is attached to hooks at G and H. Knowing that the frame supports at point C a load of magnitude P=268N, determine the tension in t..

  Determine the heat transfer through the rod

A steel rod 1 cm in diameter and 30 cm long protrudes from a steel surface at 150 C. The rod is surrounded by air at 10 C with a convective heat transfer coefficient of 10 W/m2 C. The thermal conductivity of steel is 114 W/m C. Determine the heat ..

  An instrument having a resonance frequency of 1414 rads

an instrument having a resonance frequency of 1414 rads with a damping ratio of 0.5 is used to measure a signal of 6000

  What is the average friction factor in the duct

Air enters an adiabatic duct of L/D = 40 at V1 = 170 m/s and T1 = 300 K. The flow at the exit is choked. What is the average friction factor in the duct?

  Determine the work kj performed by the piston on the

initially 0.05 kg of air is contained in a piston-cylinder device at 200 degc and 1.6 mpa. the air then expands at

  What is the highest temperature at which the flash drum can

we have a mixture that is 20 mol propane 35 mol n-butane and 45 mol n-hexane. if a flash drum operates at 400 kpa what

  Determine the number of revolution by the disk

a disk has a mass of 4kg and a radius of 90mm, it is at rest when it is placed in contact with the belt, which moves with a constat speed (v =15m/s). knowing that friction is .25 between the disk and the belt. Determine the number of revolution by..

  The elastic modulus of diamond is measured by applying a

the elastic modulus of diamond is measured by applying a force parallel to the body diagonal of the unit cell and

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd