Determine the first law thermal efficiency and compare it

Assignment Help Mechanical Engineering
Reference no: EM13618751

In a Rankine cycle, steam leaves the boiler at 400 celsius and 5MPa. The condenser pressure is 0.01MPa. The water entering the pump is saturated. Determine the first law thermal efficiency and compare it to that of a Carnot cycle operating between the same temperature extremes.

Reference no: EM13618751

Questions Cloud

A charge of 238 microc is located at 432 m 590 m and a : a charge of 23.8 microc is located at 4.32 m 5.90 m and a charge of -10.6 microc is located at -4.43 m 6.65 m. what
You believe you will need to have saved 600000 by the time : you believe you will need to have saved 600000 by the time you retire in 40 years in order to live comfortably. if the
Criminal justice class assume you are in the research : assume you are in the research planning and development unit of your police organization. your chief executive officer
Between the electrodes but not near their edges the : two flat 4.0 cm times 4.0 cm electrodes carrying equal but opposite charges are spaced 2.0 mm apart with their
Determine the first law thermal efficiency and compare it : in a rankine cycle steam leaves the boiler at 400 celsius and 5mpa. the condenser pressure is 0.01mpa. the water
Patience inc just paid a dividend of 235 per share on its : patience inc. just paid a dividend of 2.35 per share on its stock. the dividends are expected to grow at a constant
Explain what causes the seasons that we experience in the : q1. explain what causes the seasons that we experience in the temperate region of the northern hemisphere. do you have
A parking garage charges 10 for the first hour and 8 per : a parking garage charges 10 for the first hour and 8 per hour or fraction thereof after that. suppose you park in this
The tunnel is located in boulder colorado altitude 1650 m : an intermittent wind tunnel is designed for a mach number of 4 at the test section. the tunnel operated by sucking air

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Construct a suitable finite element model

Construct a suitable finite element model and compare the FEA predictions with the theoretical data and produce a graph to show the stress distribution

  Evaluate thermal efficiency of the cycle

Evaluate thermal efficiency of the cycle

  Compute the convective heat-transfer coefficient the

a liquid food is being heated in a tubular heat exchanger. the inside pipe wall temperature is 110degc. the internal

  Etimate the temperature inoc to which the block must be

at room temperature 23oc a cylinder of steel has a diameter of 15.02 mm which is too large to fit into a 15 mm diameter

  What is the correct decimal notation for the number

What is the correct decimal notation for the number 1.345 x 10-1?

  A balloon in the upper atmosphere is filled with water

a balloon in the upper atmosphere is filled with water vapor with a speci?c volume of 10 m3 kg. a if its volume is 25

  A clock is slow such that it falls behind 152 min in every

a clock is slow such that it falls behind 15.2 min in every hour. calculate the angular velocity of its second hand the

  Run a fmea analysis and suggest the possible solution

The plate fin heat exchanger uses gaskets to separate oil and water paths. Since this unit is used in trucks, vibration should also be considered. Run a FMEA analysis and suggest the possible solution to avoid future failure.

  A 49 kg person drinks 520 g of milk which has a caloric

question a 49 kg person drinks 520. g of milk which has a caloric value of approximately 3.0 kjg. if only 19 of the

  Determine the minimum thickness of fibreglas insulation

Determine the minimum thickness of fibreglas insulation that needs to be used in the wall in order to avoid condensation on the outer surfaces.

  Determine the quality of a saturated liquid vapor mixture

determine the quality of a saturated liquid vapor mixture given the data below. mvapor 9 kg mliquid 11 kgnbsp

  For the diffuser shown in the attached image find the mass

a diffuser is a device that the flow of air in order to recover a pressure loss. for the diffuser shown in the attached

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd