Determine the final pressure in the tank

Assignment Help Mechanical Engineering
Reference no: EM13707050

Consider 0.8 grams of air (which may be assumed to be an ideal gas) at 295 K and 1.5 bar trapped in a rigid tank. An electrical heater is operated for 30 seconds. During this time the voltage across the heater is 12 V and 0.6 amps pass through the resistance element. During this process, 126 J of energy is lost via heat transfer through the tank walls.

Assuming the specific heats of air are constant (at the 300 K values (use table B.9)) determine the final temperature of the air. Hint: Use the prop. relationships.

Determine the final pressure in the tank.

Reference no: EM13707050

Questions Cloud

What is the mass of the sled : A girl of mass m = 54 kg is pulling a sled up a slippery slope. The coefficient of friction between the boots of the girl and the slope is u_s = 0.157 kg. what is the mass of the sled
How high will the ball go : A Super Ball is dropped from a height of 3.50m .Assuming the ball rebounds with 90% of its impact speed less than 90% of the initial height, How high will the ball go
Describe how you would develop a scale of force : You are given 10 identical springs. Describe how you would develop a scale of force (i.e., a means of producing repeatable forces of a variety of sizes) using these springs
Obtain the surface charge density inside the hollow cylinder : A long non-conducting cylinder has a charge density p = Alpha R, where Alpha = 6.53 C/m4 and r is in meters. Concentric around it is a hollow metallic cylindrical shell. find the surface charge density inside the hollow cylinder
Determine the final pressure in the tank : Consider 0.8 grams of air (which may be assumed to be an ideal gas) at 295 K and 1.5 bar trapped in a rigid tank. An electrical heater is operated for 30 seconds. During this time the voltage across the heater is 12 V and 0.6 amps pass through the re..
How long does it take the patrol car : A speeder traveling at a constant speed of 34.7 m/s races past a stopped patrol car on the interstate. How long does it take the patrol car to reach a speed of 52.8 m/s if it starts moving just as the speeder passes
Find the maximum horizontal range over which you can throw : If you can throw a ball vertically upward to a height h = 27.0 m, what is the maximum horizontal range over which you can throw the same ball
Obtain the speed of the stone just before it hits the ground : You throw a stone vertically upward with an initial speed of 6.0m/s from a third-story office window. Find the speed of the stone just before it hits the ground
How far is he from the starting point : A jogger runs directly east for 5 km, then turns and goes northwest for 5 km. He then travels directly south for 3 km. How far is he from the starting point

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd