Determine the equivalent impedance in high-voltage terms

Assignment Help Electrical Engineering
Reference no: EM13274383

A 75-kVA, 230-V/115-V, 60-Hz was tested with these results:
Open-circuit test: 115 V, 16.3 A, 750 W;
Short-circuit test: 9.5 V, 326 A, 1200 W

Determine the equivalent impedance in high-voltage terms.

Reference no: EM13274383

Questions Cloud

Explain the heat capacity of liquid water degree celcius : The heat capacity of liquid water 4.18 J/g degree celcius and the molar heat of vaporization 40.7 kJ/mol. How many kilojoules of heat must be provided to convert 1.00 g of liquid water at 67 degree celcuis into 1.00 g of steam at 100 degrees celci..
Obtain the speed of the bullet : An 8.0g bullet is shot into a 5.0kg block, at rest on a frictionless horizontal surface. Find the speed of the bullet
Determine the induced voltage in the coil as function of tym : The sinusoidal flux in the core of a transformer is given by φ = 0.002 Sin 377t Wb. This flux links a primary winding of 100 turns. Determine the induced voltage in the coil as a function of time.
Determine the fundamental frequency of the string : A string that is fixed at both ends has a length of 1.81 m. When the string vibrates at a frequency of 84.3 Hz, a standing wave with five loops is formed.  What is the fundamental frequency of the string
Determine the equivalent impedance in high-voltage terms : A 75-kVA, 230-V/115-V, 60-Hz was tested with these results: Open-circuit test: 115 V, 16.3 A, 750 W; Short-circuit test: 9.5 V, 326 A, 1200 W Determine the equivalent impedance in high-voltage terms.
How far ahead of jill should be begin : Jack and Jill decide to have a four-lap race (i.e. 4 m meters) with each runner agreeing to run only in his/her lane. If Jack runs in lane two, how far ahead of jill should be begin if the finish line is jill's starting point?
What is the electric field vector at the origin : An semicircular arc with a radius of B is split into two. The arc is in the xy-plane such one part is in the first quadrant, What is the electric field vector at the origin
Define series reactance per phase of the transmission line : Three single-phase transformers, each rated 15 MVA, 13.2:66 kV, with a leakage reactance of 0.1 pu, are connected to form a three-phase Y-Δ bank, one side of which is connected to a 120-kV tranmission line and the other side, to three 12-ohm resis..
Explain producing ethanol as a biofuel from sugars in corn : Producing ethanol as a biofuel from sugars in corn (glucose) has become a major industry in the grain belt. This process can be summarized as follows, where glucose to form ethanol and carbon dioxide. Use bond energies to estimate Delta E for this..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Design op amp circuit to produce output vout

design op amp circuit to produce output vout which is related to inputs v1, v2 and v3 by expression vout= -(3v1+5v2+8v3). assume max permitted resistor value= 200k. use only one op amp

  Design a circuit that performs the function

The conveyor belt moves relatively slow therefore several seconds pass before the separator switches position. The piston moves two switches (N/A) when it is on position one or on position two. The control system requires a variable exit voltage b..

  Define asynchronous and synchronous communication mode

What are the respective advantages and disadvantages of the asynchronous and synchronous communication modes from a reliability perspective?

  Determine the tranfer function of the thermocouple

During calibration, and iron/constantan thermocouple is zeroed( set to emit a Zero Voltage) AT 0 DEGREES CELCIUS. At 750 degrees celcius, it emits a voltage of 38.8mV. Alinear Out/input relationships exists between 0 and 750 degrees celcius.

  How to evaluate power dissipated in the components

how to evaluate power dissipated in the components of an RLC series circuit by using matlab software?

  Expand the memory unit to a ram using two 7489ics

Expand the memory unit to a 32x4 RAM using two 7489ICs ( you might use the HM6116A120 chip for the Multisim Program Simualtion). Use the CS inputs to select between the two ICs. Note that since the data outputs are 3-stated

  Design uv flip-flop using a jk flip-flop and two logic gates

Design a UV flip-flop using a JK flip-flop and two logic gates. where the characteristic table for the UV flip flop is U V Q(t+1) 0 0 1 0 1 !Q(t) 1 0 Q(t) 1 1 Q(t)

  Why does the thevenins technique work only for circuits

Why does the Thevenin's technique work only for circuits with linear elements (or at most a single non-linear resistor). Figure out where the mathematics of the theorem breaks down for non-linear elements and why

  Calculate what current is in the transmission line

Electricity is distributed from electrical substations to neighborhoods at 15,000 Volts, to a transformer on utility poles near homes, where is it stepped down to 120 Volts for household use.

  Determine the state diagram for the moore machine

A finite state machine has one input, X, and one output, Z. The output becomes 1 and remains 1 thereafter when, starting from reset, at least two 1s and one 0 have occurred as inputs, regardless of the order in which they appeared.

  Calculate the normal force fn for 300 g and 150 g

Assume the mass of the cup and water to be equal to the mass of water alone. Calculate the normal force FN for 300 g and 150 g.

  Determine what is the secondary voltage

The low-voltage winding of a transformer has 200 turns, and the high-voltage coil has 11,000 turns. The transformer is operated as a step-down transformer, and 13.2KVolts is impressed on the primary side.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd