Determine the efficiency of the resulting codes

Assignment Help Electrical Engineering
Reference no: EM131208289

A source output consists of four messages [m1,m2, m3, m4] with respective probabilities [0.35, 0.3, 0.2, 0.15]. Determine the binary code words for the second-order source extension using the Shannon-Fano and Huffman coding techniques. Determine the efficiency of the resulting codes and comment on the results.

Reference no: EM131208289

Questions Cloud

Researching wan connectivity options : Research major wide area networking (WAN) technologies and protocols that allow for the connecting and transfer of data between remote sites. The three WAN technologies and protocols you will be researching are
Describe how your career choice will be affected : What insights have you gained and how can I explain those insights? How does concept relate to you and what will you do with? Are there questions or weaknesses or issues with the concept that needs explaining or modifying or adapting? What are they?
Sending real-time voice from host : We are sending real-time voice from Host A to Host B over a packet switched network (VoIP) Host A converts analog voice into a digital 64 kbps bit stream on the fly. Host A then groups the bits into 56-byte packets.
Should not be separated to achieve adequate internal control : Explain why each of the following combinations of tasks should or should not be separated to achieve adequate internal control.
Determine the efficiency of the resulting codes : Determine the binary code words for the second-order source extension using the Shannon-Fano and Huffman coding techniques. Determine the efficiency of the resulting codes and comment on the results.
Develop the function qwerty : Develop the function qwerty. The function consumes a counting number and extracts that many keyboard characters from the string "qwerty".
Prepare a discussion post about jefferson and slavery : Prepare a Discussion post about Jefferson & Slavery. Your initial Discussion post should address everything asked and be a minimum of 200 words, which is about 1/3 of a page on a normally formatted Word document.
Assignment-setup a network : This is a two part assignment in which you will first set up a network that will then be used to build access lists.
Paper-impact of cultural dimensions on worldviews : Paper: Impact of Cultural Dimensions on Worldviews What kinds of ideas about organizational life may be generated by people of varying ages, with differing family structures, and of different sexes and gender roles

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Sketch two periods of the output signals out1 and out2

Channel 1 and channel 2 are configured to generate output signals OUT1 and OUT2, with TACCR1 = 745, and TACCR2 = 499, respectively. And the output mode is set to Reset/Set. Sketch two periods of the output signals OUT1 and OUT2 (with proper labeli..

  What does mean by term slip of three phase induction motor

what do u mean by term slip of three phase induction motor  calculate the slip of 4-pole induction motor running at 1470 rpm while bieng connected to a 50 hz three phase source

  Would si doped with arsenic be useful in the applications

A semiconductor device requires n-type material; it is to be operated at 400K. a) would Si doped with 10^15 atoms/cm^3 of Arsenic be useful in this applications. b) Could Ge doped with 10^15 cm^-3 antimony be used.

  Determine what is the transverse periodicity of the object

If the self-imaging planes are 1 cm apart, what is the transverse periodicity of the object. Assume the wavelength of illumination as 1 micron. find the locations of the planes where one can observe contrast reversal.

  Compare the equivalent and nominal n circuits for the line

Assuming a positive sequence operation, calculate the exact ABCD parameters of the line. Compare the exact B parameter with that of the nominal n circuit. Also compare the equivalent and nominal n circuits for the line.

  Determine what is the value of source current

An input signal of 10V at 0o is applied to a parallel RLC circuit with resistor R = 100 , inductive reactance XL = 100 , and capacitive reactance XC = 200 . All three components are connected in parallel to the source. what is The source current.

  What is the total momentum of the wo blocks after collision

a 2.0-kg block is moving right at 1.0 m/s just before it strikes and sticks to a 1.0-kg block iniially at rest. what is the total momentum of the wo blocks after the collision

  Will the hemispheres come apart

The demonstration would end with the opening of a valve that removed the vacuum and allowed the hemispheres to separate. Suppose that the diameter of the sphere is 50 cm and the sphere is completely evacuated. The sphere is hung from the ceiling a..

  Design a circuit which accepts 2-bits input duty

Connect the PWM output to an LED, for preliminary testing with slow clock frequency, then to the oscilloscope to show final results with multiple frequencies between 10 KHz to 1MHz. In the final demonstration, connect CLK to CH1, and PWM to CH2

  Find maximum reverse voltage that will appear across diode

The rectifier feeds a load of 200 W and is fed from the linevoltage (120 Vrms, 60 Hz) through a transformer. The diodesavailable have a 0.7 V drop when conducting. If the designer opts for a half wave rectifier circuit

  Give the fourier transform of the signals that can be obtain

Any causal signal x(t) having a Laplace transform with poles in the open-left s-plane (i.e., not including the jΩ axis) has, as we saw before, a region of convergence that includes the jΩ axis, and as such its Fourier transform can be found from i..

  Write a program in basic to implement a pid controller

Write a program in BASIC to implement a PID controller

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd