User Account

All Pages

Determine the duty cycle d

Assignment Help Electrical Engineering
Reference no: EM131057407

A buck converter is supplied by a DC source of 48V. It produces an output voltage of 18V across a 10? load resistor. Assume that the capacitor is large enough so that the output voltage is kept constant. Determine the duty cycle D.

Reference no: EM131057407

Questions Cloud

Determining the armature coresheets : Why the armature core in d.c machines is constructed with laminated steel sheets instead of solid steel steel?
Calculate the number of turns on its primary : A 1100/400 V, 50 Hz single phase transformer has 100 turns on the secondary winding. Calculate the number of turns on its primary.
Analog-to-digital conversion : Assume a 4-bit successive approximation analog-to-digital converter (ADC) with Vref=5.0 volts. Assuming Vin=3.50 volts, show the operation of the ADC for each bitof the analog-to-digital conversion.
How does dn differ qualitatively from volume mean diameter : How does DN differ qualitatively from the volume mean diameter Dv
Determine the duty cycle d : A buck converter is supplied by a DC source of 48V. It produces an output voltage of 18V across a 10? load resistor. Assume that the capacitor is large enough so that the output voltage is kept constant. Determine the duty cycle D.
Determine the rms output voltage : Determine the rms output voltage, the rms source current, the rms and average currents through SCRs, and the power factor.
Meaning of regenerative braking : 1. What is the meaning of regenerative braking? 2. What are the advantages of star-delta starter with induction motor 3. Why ELCB can't work if N input of ELCB do not connect to ground?
Determine the firing angle : 1. Determine the firing angle α to obtain the rated torque at 1200rpm. 2. Compute the firing angle for the rated breaking torque at -1800rpm.
Reluctance of a material : What is the reluctance of a material that has a length of 0.07 m, a cross-sectional area of 0.014 m2, and a permeability of 4,500 u Wb/At × m?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is spectral density at 200 khz from carrier frequency

Calculate the Fourier Transform of f(t) = 5 sinc(-2t/100), and graph the magnitude and phase as a function of f. If the signal of problem 1 is delayed by 0.1 ms. What is the new Fourier Transform.

  Calculate the voltage across capacitor c2 in a circuit

Assume all the capacitors in the circuit below were discharged prior to assembly. The capacitors, resistors, and voltage sources are then arranged as shown in the circuit below. The circuit is then allowed to stabilize.

  Determine the force acting on the point charge due to e

A disk located at 0

  Compute the complex power and relate it to the average power

Consider a circuit consisting of a sinusoidal source vs(t) = cos(t)u(t) volts connected in series to a resistor R and an inductor L and assume that they have been connected for a very long time. (a) Let R=0 and L=1 H. Compute the instantaneous and ..

  Determine the high-pressure turbine work per unit mass

The temperature of steam at the inlets of both turbines is 500°C, and the enthalpy of steam is 3185 kJ/kg at the exit of the high-pressure turbine, and 2247 kJ/kg at the exit of the low-pressure turbine. Disregarding the pump work, determine the w..

  Calculate the output noise power and noise voltage

A three-stage amplifier is shown. The operating bandwidth is 500 KHz at a temperature od 25 degrees C. The output load is 1000 ohms. calculate the total NF as a number, calculate the output noise power, and calculate the output noise voltage.

  Determine the conduction parameter and threshold voltage

Consider a GaAs MESFET. When the device is biased in the saturation region,Id=18.5 micrroamp,Vgs=.35 and Id=86.2 micro amp,Vgs=.5 determine the conduction parameter and k and threshold voltage Vth

  What is maximum current that resistance can conduct safely

a) What is the total resistance corresponding to 1kohm, 4kohm, 10kohm, 4.7kohm resistors connected in series b) What is the total resistance corresponding to 10ohm, 100ohm, 1kohm, 10kohm resistors connected in parallel

  What is the approximate bit error probability of psk system

Consider a 16-ary PSK system with symbol error probability PE = 10-5. A Gray code is used for the symbol to bit assignment. What is the approximate bit error probability

  Determine what is the transverse periodicity of the object

If the self-imaging planes are 1 cm apart, what is the transverse periodicity of the object. Assume the wavelength of illumination as 1 micron. find the locations of the planes where one can observe contrast reversal.

  What maximum current will be drawn from the output

What maximum current will be drawn from the 5V output of a peripheral device connected to an HCS12 input port. What input resistance does this represent.

  Calculate the new depth of water in the conical tank

a closed conical tank with diameter of 1.50 and height of 3.00 m, sitting on its circular base has 1.00m depth of water. Suppose the tank is upside down and is made to stand vertically that way using some device.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd