Determine the control resolution for this robot

Assignment Help Mechanical Engineering
Reference no: EM13212603

The linear joint (Type L) of a certain industrial robot is actuated by a piston mechanism. The length of the joint wehn fully retracted is 600 mm and when fully extended is 1000 mm. If the robot's controller has an eight-bit storage capacity, determine the control resolution for this robot.

Reference no: EM13212603

Questions Cloud

How should manager of largo publishing house adjust input : The Largo Publishing House uses 400 printers (workers) and 200 printing presses to produce books. A printer's wage rate is $20 per hour and the price per hour of a printing press is $5,000. The last printer hired added 20 books (per hour) to total..
Find the maximum temperature in wall : The heat transfer convection coefficient between the wall and the fluid is 500 W/m2.K. Find the maximum temperature in wall.
Compute the ph value of nh3 solution : Calculate the pH value of solution (a) after 10.0 mL of NH3 solution have been added and (b) after 25.0 mL solution have been added (Ka for NH4+ = 5.6 x 10^(-10).)
What will be the final temperature in the tank : what will be the final temperature in the tank? how much work will be accomplished over the course of the entire process?
Determine the control resolution for this robot : The linear joint (Type L) of a certain industrial robot is actuated by a piston mechanism. The length of the joint wehn fully retracted is 600 mm and when fully extended is 1000 mm. If the robot's controller has an eight-bit storage capacity, dete..
Find the cross-price elasticity of demand : What is the relationship between goods x and y? Explain carefully. Using income as your primary factor, identify what category Good X falls into. Find the price elasticity of demand. Find the income elasticity of demand. Find the cross-price elast..
Determine the net electric output : Water enters a hydraulic turbine through a 30-cm-dia pipe. The pressure drop in the turbine is measured by a mercury manometer to be 1.2 m. For a combined turbine-generator efficiency of 83%, determine the net electric output. Disregard the effect..
Explain what is the molar mass of the enzyme : Assuming the density of the solution is 1.00 grams/mL, what is the molar mass of the enzyme?
Discuss the trade-off of risk : Identify a "risky" and a "safe" investment and provide rationale to justify your choices. Also, discuss the trade-off of risk and reward between your two investments.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the velocity of each car after all collisions

Knowing that the coefficient of restitution is 0.8 between B and C, and 0.5 between A and B, Determine the velocity of each car after all collisions have taken place.

  How much ideal effort force is required to travel up ramp

If a person and a wheelchair have a mombined weight of 185 lb how much ideal effort force is required to travel up the ramp? Can you just explain to me what equation I need for this?

  What force must be applied to the plunger

the pressure in the vein is known as 1850 Pa. what force must be applied to the plunger, so that 1.5 x 10^-6 m^3 of solution can be injected in 5.0 s?

  Find the natural frequencies of oscillation

find the natural frequencies of oscillation of the double-pendulum below where m1=m2=m, and L1=L2=L.

  Determine the latent heat of vaporization of the water vapor

How would you calculate the sensible heat, the latent heat, and determine the latent heat of vaporization of the water vapor in this air stream as the air is cooled from 170 F to 48 F?

  Explain state refrigeration system as saturated vapor

Refrigerant 134a enters a heat exchanger in a steady state refrigeration system as saturated vapor at 0 °F and exits at 20 °F with no change in pressure.

  Determine the designe power

determine the designe power. An output speed of 175 RPMis specified. Determine: a) number of teeth on the small sprocket, b) number of teeth on the large sprocket, c) lubrication type required, d) the required length of chain (in inches) if the ce..

  Apparent density and theoretical density and void volume

Apparent Density, Theoretical Density and Void Volume, A compacted body of iron powder is sintered into a 20mm-diameter, 45-mm-tall cylinder which, upon weighing

  Determine an expression for the number of cycles to failure

Determine an expression for the number of cycles to failure, Nf if the initial crack size is a0. State any assumptions you make.

  A hydraulic cylinder is diameter

A hydraulic cylinder is 100mm diameter and is fed by a pipe 15mm in diameter. If the piston in the cylinder moves forward at a rate of 0.2ms^1

  Carrying a uniformy distributed load

The bending moment M at position x m from the end of a simply supported beam of lenght L m carrying a uniformy distributed load of w Kn m-1 is given by

  Unidirectional reinforced composites

Calculating the mechanical properties of unidirectionally reinforced composites

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd