Determine the components of the force q in directions

Assignment Help Mechanical Engineering
Reference no: EM131384003

An architect specifies the roof geometry shown for a building. Each of lines EAB, BD, DCG, EG, and AC are straight. Two forces of magnitude P and Q acting in the -y direction are applied at the positions shown.
Determine the components of the force Q in directions normal and parallel to the roof at point C. Express your answer in terms of Q.

2484_d509eb83-1912-45ed-9823-ac89bf6369b8.png

Reference no: EM131384003

Questions Cloud

Find the work done by f : Find the work done by F, and the increase in kinetic energy of P, during the time interval 0 ≤ t ≤ 1. What principle does this illustrate?
Find the rate of working of the man : An athlete putts a shot of mass 7 kg a distance of 20 m. Show that the athlete must do to at least 700 J of work to achieve this.
What makes a top 100 hospital : HSM310: "What Makes a Top 100 Hospital?" Your assignment is to visit the website of one of the top 100 hospitals on the list in this link: Top 20 out of Top 100 Hospitals. After reviewing the hospital and health system and analyzing its services a..
Find the work needed to lift a satellite of mass 200 kg : Find the work needed to lift a satellite of mass 200 kg to a height of 2000 km above the Earth's surface. [Take the Earth to be spherically symmetric and of radius 6400 km. Take the surface value of g to be 9.8ms-2.]
Determine the components of the force q in directions : Determine the components of the force Q in directions normal and parallel to the roof at point C. Express your answer in terms of Q.
How far does p get along the positive x axis : When P reaches the origin, it experiences the force F = -K x2, where K is a positive constant. How far does P get along the positive x-axis?
Find the normal frequencies and the form of the normal modes : Find the normal frequencies and the form of the normal modes for this system. Write down the form of the general motion.
Discuss how the service industry may change : Discuss how the service industry may change in the next 10 to 20 years in terms of delivering quality service to its customers.Propose one service innovation that may enhance the quality of the food service industry in the near future. Provide an e..
Determine the angular velocity of each of the three bars : Determine the angular velocity of each of the three bars at that instant. Ref: http://www.transtutors.com/questions/bar-ab-is-rotating-counterclockwise-and-at-the-instant-shown--401861.htm

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Steam flows steadily through a turbine at a rate of 47000

steam flows steadily through a turbine at a rate of 47000 lbmh entering at 1000 psia and 900 degrees f and leaving at 5

  What is the value of the constant c in units of mm k

At what wavelength does the energy distribution du/dε from our Sun peak, if the visible surface acts like a blackbody of temperature 5800 K?

  Compute flow area and hydraulic radius for circular drain

For the channel designed in Problem 14.32, compute the normal discharge that is expected for a slope of 0.12 percent if the channel is made from painted steel.

  Before being injected into a furnace pulverized coal is

before being injected into a furnace pulverized coal is preheated by passing it through a cylindrical tube whose

  One kilogram of water contained in a sealed piston-cylinder

one kilogram of water contained in a sealed piston-cylinder assembly initially at 160degc and 200 kpa undergoes an

  Ten 10 kg of water at 100 degrees c expands in a piston and

ten 10 kg of water at 100 degrees c expands in a piston and cylinder arrangement from a volume of 0.1 m3 to a final

  Axial strain gauges were installed on outer surface

A cylindrical Steel compression specimen of 150 mm long, 75.60 mm outside diameter and 69.60 mm inside diameter is used to determine the stress distribution in a compression member. An axial force P = 100 kN is applied at different locations (A, B, o..

  Determine initial upward acceleration

If it hovers over the land in a fixed position and then releases 50 kg> s of water at 10 m> s, measured relative to the helicopter, determine the initial upward acceleration the helicopter experiences as the water is being released.

  A shell-and-tube heat exchanger consisting of one shell

a shell-and-tube heat exchanger consisting of one shell pass and two tube passes is used to transfer heat from an

  Define the terms in this expression also sketch label and

the potential energy term which describes the bonding between dissimilar ions in an ionic solid may be given as

  Find the approximate modelling solution to evaluate

With your problem solving and modelling skills to consider more advanced problems using the finite element method. i.e, A single layer, homogeneous structure subject to a cyclic temperature change on one side

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd