Determine the characteristic roots for the system

Assignment Help Electrical Engineering
Reference no: EM13292916

An LTI system's impulse response is described by the differential equation, dh(t)/dt + 3h(t) = impulse function. Find the characteristic roots for the system, the initial condition, and the h(t) for t > 0.

Reference no: EM13292916

Questions Cloud

Determine the time of operation over current relay : Determine the time of operation of 5A , 3 Seconds over current relay having a current setting of 150% and a time setting multiplier of 0.8 connected to supply circuit through a 500/5 current transformer when the circuit carries a fualt current ..
Evaluate the width of the slit : For a demonstration, a professor uses a razor blade to cut a thin slit in a piece of aluminum foil. evaluate the width of the slit
Explain the pyrene excimer emission spectrum : The pyrene excimer emission spectrum at a (higher/lower/same) wavelength than (as) the excited pyrene fluorescence emission spectrum. Explain.
The eoq is particularly sensitive to which of the following : The EOQ is particularly sensitive to which of the following?
Determine the characteristic roots for the system : An LTI system's impulse response is described by the differential equation, dh(t)/dt + 3h(t) = impulse function. Find the characteristic roots for the system, the initial condition, and the h(t) for t > 0.
What is the maximum inventory level : In a non instanteneous receipt model, daily demand is 55 units and daily production is 120 units, Co=$70 and Cc=$4 per unit per year. What is the maximum inventory level? (Assume that the facility is open 365 days per year.
Define the solution becomes quite warm : A solution is made by dissolving 25.7 g of NaOH in approximately 450 mL of water in a volumetric flask. The solution becomes quite warm, but after it is allowed to return to room temperature, water is added to total 500 mL of solution
What will be the result of compiling code : What will be the result of compiling following code.
Explain the half-life of methylmercury in the human body : The half-life of methylmercury in the human body is estimated to be close to 100 days. Suppose a person weighing 65 kg eats 0.5 kg of fish containing 0.5

Reviews

Write a Review

 

Electrical Engineering Questions & Answers

  Determine the effective data rate in bps

Two DTEs are communicating via modems and RS-232C interfaces over a half duplex link. Data transmission is one directional with each message of length M. After a message is transmitted, the sender waits for a CTS message.

  Write down the principle of energy conversion

Write down the principle of energy conversion and give an example for single and double excited system.

  How many silicon atoms are present for each lattice impurity

Assume that each donor atom contributes one free electron to the silicon lattice. For an n-type doping of 5x10^15 cm-3, how many silicon atoms are present for each lattice impurity

  Calculate the voltage drop across the capacitance

a)For what value of capacitance will these condition exist ,assuming that impressed voltage ,frequency,resistance and inductance remain unchanged. b)Calculate the voltage drop across the capacitance under this condition.

  Find the carrier mobility and carrier density

A "Hall bar" specimen is 250 mm long, 12 mm wide, and 1.5 mm thick. Along the 250 mm direction (+x), +5 V drives a current of +1.75 mA. Along the 1.5 mm direction (+z) a magnetic field of 1 Tesla is applied.

  What must be relation between a and b in order that evanish

Two infinitely long coaxial cylindrical surfaces, r = a and r= b (b > a), carry surface charge densities Dsa and Dsb,respectively. (a) Determine the electric field intensity everywhere. (b) What must be the relation between a and b in order that Eva..

  Calculate the resistance of the load

The high-voltage side of a transformer has 750 turns, and the low voltage side has 50 turns. When the high side is connected to rated voltage of 120 V, 60 Hz, a rated load of 40 A is connected to the low side.

  Whether an fet is operating in ohmic region or active region

Discuss the operation of a JFET, including the pinch off and gate-source cutoff voltage in your explanation. Discuss how you can tell whether an FET is operating in the ohmic region or the active region.

  How tall must the antennas be if the link operates

How tall must the antennas be if the link operates on a frequency of 2.450Ghz, D1=5miles, D2=11miles, and the obstruction is 60 feet high?

  What is the minimum power rating for each resistor

The voltage across the load must remain between 4.7 and 5.0 V for all values of load current. Come up with (draw) a voltage-divider network to supply the load. You may assume that resistors of any value desired are available.

  Determine the appropriate sop equations

Using this method, create and test a minority vote circuit, a circuit designed to indicate when one or no inputs are HIGH. Determine the appropriate SOP equations, enter, compile, simulate, download, and test your solution.

  Determine range of values for t that allow complete recovery

Let y(t) he the signal at the output of the LTI system when x(t) is the input signal. The following signals are sampled using a train of impulses with periodicity T, signal x(t) is sampled to obtain xc(t), and signal y(t) is sampled to obtain yc(t..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd