Determine the change in specific entropy kjkg-k for air

Assignment Help Mechanical Engineering
Reference no: EM13618829

1) Initially, an insulated rigid tank contains 2.85 kg of water at 263oC and 1 MPa. A heater in the wall of the tank maintains the wall temperature at 600oC. After a period of time, the pressure in the tank rises to 1.5 MPa. Determine the total entropy generation (kJ/K) during this process.

2) Steam at 1 MPa, 609.4oC, expands in a turbine to 0.01 MPa. If the process is isentropic, find the work per unit mass (kJ/kg) produced by the turbine.

3) Determine the change in specific entropy (kJ/kg-K) for air undergoing a process from state 1 (T1 = 300 K, P1 = 109 kPa) to state 2 (T2 = 876 K, P2 = 467 kPa). Assume variable specific heats (use the ideal gas tables). Your answers may vary slighly (< 1%) from the given answer.

Reference no: EM13618829

Questions Cloud

A pile driver drives a post into the ground the mass of : a pile driver drives a post into the ground. the mass of the pile driver is 3500 kg and it is dropped through a height
Nitrogen gas flows into a convergent nozzle at a pressure : 1 nitrogen gas flows into a convergent nozzle at a pressure of 225kpa a temperature of 440k and with a very low inlet
An experimenter wants to conduct a hypothesis test on a : an experimenter wants to conduct a hypothesis test on a claim that there was no difference between two population
When an electron circles in a uniform circular motion what : when an electron circles in a uniform circular motion what would happen if we increased the magnitude of the magnetic
Determine the change in specific entropy kjkg-k for air : 1 initially an insulated rigid tank contains 2.85 kg of water at 263oc and 1 mpa. a heater in the wall of the tank
The second sample of 40 items were chosen and measured this : a two-sample t test is going to be carried out where it is assumed that the population variances are unknown but
A michelson interferometer is set up to produce circular : a michelson interferometer is set up to produce circular fringes using a krypton source of wavelength 605.8 nm. find
Calculate the average distance moved in one day by smoke : calculate the average distance moved in one day by smoke particles in air for the following cases a smoke diffuses in
By measuring the go-and-return time for a laser pulse to : by measuring the go-and-return time for a laser pulse to travel from an earth-bound observatory to a reflector on the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the turbine inlet temperature

Determine the turbine inlet temperature, the cycle thermal efficiency, and the back-work ratio of this cycle.

  Compute the required diameter for a solid circular shaft if

compute the required diameter for a solid circular shaft if it is transmitting a maximum of 110hp at a speed of 560

  A 2mm diameter metor of specific gravity 29 has a speed of

a 2mm diameter metor of specific gravity 2.9 has a speed of 6 kms at an altitude of 50000m where the density of air is

  The hole must have a diameter of b 25 mm determine the

the aluminum plate of thickness t 3.5 mm. is to be designed so the maximum stress remains below 100 mpa. the hole must

  1 write a program that takes the image tracksjpg and finds

1 write a program that takes the image tracks.jpg and finds canny edges and then finds lines in these edges using the

  Knowing that it strikes the water 4 s after release

a stone is thrown vertically upward from a point on a bridge located 40 m above the water. knowing that it strikes the

  Knowing that at the instant shown the rod has an angular

the motion of the uniform slender rod of length l0.5 m and mass m 3 kg is guided by pins at a and b that slide freely

  It is assumed that the wire surface temperature is constant

an electrical wire having a diameter of 1.5 mm and covered with a plastic insulation thickness 2.5 mm is exposed to

  Develop a system of equations and solution

Depron is a polystyrene foam, popular as a material for the manufacture of fast food trays and packaging. It is much lighter than balsa wood and can be cut with a sharp blade, sawn with a fine.

  Determine the channel height that can be used to determine

a for a rectangular coordinate system we developed the navier stokes equation for vx. now reduce that equation to

  A compressor installed at a whalf for loading container

a compressor installed at a whalf for loading container ships is able to provide 6 bar.g pressure into the pressure

  Determine the stress in a stay at a given temperature

Determine the stress in a stay at a given temperature. A steel 'stay' of effective length 5m is fitted in between the walls of a ships refrigerated compartment when the temperature is 18 degrees centigrade.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd