Determine the average power delivered to the load

Assignment Help Electrical Engineering
Reference no: EM131131983

The load for the following circuit is given by the 5 ohm resistor and the 0.02297 Henry inductor. In addition, vin(t) = 200 sin(377t) volts. Determine the average power delivered to the load.

838_a2b1a2a3-53ac-4071-95c4-2108ffa81a35.png

Reference no: EM131131983

Questions Cloud

Define the terms diversity and affirmative action : Define the terms Diversity, Affirmative Action, Surface-Level Diversity, Deep Level Diversity and Social Intergration - If you were the judge in this case, what would you do?
How are dividends in arrears presented in the financial : What are the principal differences between common stock and preferred stock?
Hy do many firms finance/invest at a level below this optimu : How can a firm use the WMCC schedule and the IOS to find the level of financing/investment that maximizes owner wealth? Why do many firms finance/invest at a level below this optimum?
Evaluate principles of software engineering aspects : Demonstrate their ability to interpret a set of laws that are part of the principles of software engineering, to evaluate principles of software engineering aspects within an industry in relation to the various elements covered
Determine the average power delivered to the load : The load for the following circuit is given by the 5 ohm resistor and the 0.02297 Henry inductor. In addition, vin(t) = 200 sin(377t) volts. Determine the average power delivered to the load.
How each applies to function practiced in your place of work : Analyze the application of these management concepts to your place of work; the paper will not simply be a report on the five functions in general. Identify specific examples and explain of how each applies to the functions practiced in your place ..
What effect does this transaction have on : The treasury stock purchased in question 14 is resold by Kwun, Inc. for $18,000.What effect does this transaction have on
What is the investment opportunities schedule : What is the investment opportunities schedule (IOS)? Is it typically depicted as an increasing or a decreasing function? Why?
What is the weighted marginal cost of capital : What is the weighted marginal cost of capital (WMCC)? What does the WMCC schedule represent? Why does this schedule increase?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find the value of the total circuit complex impedance

An input signal of 10V at 0o and a frequency of 1592 Hz is applied to a series RLC circuit with resistor R = 100 ohm, inductor L = 20 mH, and capacitor C = 0.5 F. The value of the total circuit complex impedance is.

  Determine the new kva and power factor

The torque to force the machine to break from synchronism if the excitation is reduced that the generated e.m.f is 4kV (phase)

  Calculate per-phase current that has to be carried by cables

It operates at a power factor of 0.85 (lagging) at its rated conditions. Calculate the per-phase current that has to be carried by the cables to the power electronics converter and the step-up transformer located at the base of the tower.

  What is energy stored at switch closed

For a RL circuit, write a diffedrential equation in which the only time dependant quantity is current (use Kirchoff's loop). Derive an expression for current, i(t), in terms of L,R, and Vo. If Vo=5V, R=2.5 ohms, L=100 nH

  Least-mean-square agorithm to perform pattern classification

Repeat the computer experiment of Section 10.21, this time using the recursive leastsquares (RLS) algorithm in place of the LMS algorithm.

  Determine the dynamic behavior of the tank concentrations

Determine the dynamic behavior of the tank concentrations (CA0 and CA) in response to a step change in inlet concentration by 0.925 mole/m3. Estimate the time it takes until 63% of the change in outlet concentration, CA has occurred.

  Determine what is the potential of the body now

A body attached to earth ground by an electrical conductor is at zero electrical potential. A charge of 25 C is added to the body. What is the potential of the body now. Explain.

  Determine required sampling rate and the line speed

Consider a PCM-TDM system in which 24 signals are to be processed. Each signal has a baseband bandwidth of 3 KHz. The sampling rate has to be 33.3% higher than the theoretical minimum, and 8 bits are to be used.

  Calculate the capacitive reactance

Calculate the capacitive reactance/ph such that the load power factor is increased to 0.98 lag and calculate the percentage reduction in line current with this value of capacitive reactance in circuit.

  Why depletion layer charge appears for 2-dissimilar material

Explain with necessary derivation and EM details, why depletion layer charge appears when two dissimilar semiconductors(such as P and N materials) are combines to form a common junction.

  Determine the location of the point charge of a line charge

A line charge with density 2nC/m exists at y= -2, x=0. Find the electric field intensity at the origin. Now we wish to place a point charge Q=8nC at such a point so that the total electric field is zero at the origin. Determine the location of the..

  Determine what is breakdown potential with aluminum foil

Construct aCapacitor You are asked to construct a capacitor having a capacitance near 1 nF and a breakdown potential in excessof 10,000 V. You think of using the sides of a tall Pyrex drinkingglass as a dielectric, lining the inside and outside cu..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd