Determine the average-peak and rms inductor currents

Assignment Help Electrical Engineering
Reference no: EM13264529

A buck converter has an input of 6 V and an output of 1.5 V. The load resistor is 3 , the switching frequency is 400 kHz, L 5 H, and C 10 F.
(a) Determine the duty ratio. (b) Determine the average, peak, and rms inductor currents. (c) Determine the average source current. (d) Determine the peak and average diode current.

Reference no: EM13264529

Questions Cloud

What is the bonds yeild to maturity : An 8-year bond for Katy Corporation has a market price of $700 and a par value of $1000. If the bond has an annual interest rate of 6 percent, but pays interst semiannually, what is the bond's yeild to maturity?
Explain what is the rate of disappearance of h2(g) : The rate of formation of ammonia in the reaction N2(g) + 3 H2(g) ? 2 NH3(g) was reported as 1.15 M/h (moles per liter per hour). What is the rate of disappearance of H2(g)
Find the magnitude of the electrons acceleration : An electron passes through a point 3.27 cm from a long straight wire as it moves at 37.3% of the speed of light, Find the magnitude of the electron\'s acceleration at that point
What should be the price of abcs bonds : You also know that bonds with similar risk are selling at YTM of 15%. What should be the price of ABCs' bonds?
Determine the average-peak and rms inductor currents : A buck converter has an input of 6 V and an output of 1.5 V. The load resistor is 3 , the switching frequency is 400 kHz, L 5 H, and C 10 F. (a) Determine the duty ratio. (b) Determine the average, peak, and rms inductor currents.
How far from the cliff must the ship be : A ship at sea has its radio transmitting antenna at a 10 m height above the surface of the water. how far from the cliff must the ship be
How to draw a virtual trail map in processing : How to draw a virtual trail map in Processing? with camera view and able to make an object running?walking to a specific location. Then by using mousepressed,can click the specific location,in order to provide more information on that specific locati..
Find and plot the first 4 samples of the output : Given an input signal x[n] whose sample values are given in the table below. Find and plot the first 4 samples of the output that results when this input is applied to the two filters below: (Use n=0, 1, 2,3) A: Filter 1 Equation: y[n] = x[n] - 0.5..
Mtv networks-the arabian challenge : Experts felt that one of the biggest challenges faced by MTV while launching MTV Arabia was the prevalent culture in the Arab world. Discuss the Arab culture. What challanges does the culture pose to MTV?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Schematic for the logic to implement circuit using inverter

a) Draw the state diagram b) Draw the schematic for the logic to implement this circuit using Inverters, AND gates, OR gates and D flip flops. Use the reverse side and additional sheets if needed.

  Solar energy for farms in middle east

Determine the energy uses on farms in middle east and determine whether or not it is better to use a stand alone system or a grid connected system for the application on farms.

  Find the first five samples of the impulse response

Given the following IIR system with zero initial conditions: y[n]=0.2 x[n]- 0.5y[n-1] -0.06y[n-2] a)find the first five samples of the impulse response b) find the first five step response

  Determine the rms values of vc-vl and vr

If it is possible to determine whether a circuit is in resonance given only the RMS values, explain how it could be done. If it is not possible, explain what further information you would have to have.

  Calculate what is the effective voltage in vrms

Calculate the following. a) What is the magnitude of the voltage in a wall socket if the effective voltage is 240 Vrms b) What is the magnitude of the current if the effective current is 360 mArms

  Find the value of land c at resonance

The cutoff frequencies of a series resonant circuit are 5400 Hz and 6000 Hz. a. Find the bandwidth of the circuit. b. If Qs is 9.5, find the resonant frequency of the circuit.

  Calculate the power required for the field as a percentage

Two dc motors are compared. the first one is a 4hp dc motor which draws a current or 0.7A when the field is connected to a 150V source. the second, a 600 hp motor draws a field current of 5A when the field is connected to a 300V dc source.

  Derive the equation for the output voltage charging behavior

For the grounded gate p-pullup pseudo NMOS circuit shown below assume the load capacitor, CL, is initially discharged, and that the input voltage abruptly drops from Vdd to zero. Derive the equation for the output voltage charging behavior.

  Find value of capacitance needed to bring current in phase

single phase motor draws 20A from a 200V, 50Hz supply with a lagging power factor of 0.8. Calculate the value of the capacitance needed to bring the current in phase with the voltage.

  What is minimum coefficient of friction that prevent sliding

what is the minimum coefficient of friction that will prevent sliding.

  Design the sign extension component of an i-format data

design the sign extension component of an I-Format Data Path Unit, where a 16 bit number will be extended to a 32-bit number, while mainintaing the sign (signed numbers use 2s complement).

  Find what is the instantaneous frequency of the signal

A phase modulation is used to transmit the signal s(t) = 10cos(20*pi*t) + 5sin(10*pi*t). kp = 3 rad/volts and fc = 20MHz a) What is the instantaneous frequency of the signal b) Write down the expression of the transmitted signal.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd