Determine the approximate drag coefficient for the parachute

Assignment Help Mechanical Engineering
Reference no: EM131369982

1. The drag coefficient for a newly designed hybrid car is predicted to be 0.21. The cross-sectional area of the car is 30 ft2. Determine the aerodynamic drag on the car when it is driven through still air at 55 mph.

2. A 5-m-diameter parachute of a new design is to be used to transport a load from flight altitude to the ground with an average vertical speed of 3 m/s. The total weight of the load and parachute is 200 N. Determine the approximate drag coefficient for the parachute.

Reference no: EM131369982

Questions Cloud

Discuss the varying degree of ethics found in organizations : Discuss the varying degree of ethics found in organizations you have worked for and how these cultures affected you and / or your work. Then, discuss how you know you are part of an ethical organization.
Diverse leadership and promoting diversity : Do you agree that diverse leadership and promoting diversity in the workforce is a competitive advantage. Why? What is the most compelling business argument for or against diverse leadership teams? In what ways can diversity lead to quality improveme..
What you believe to be the top ten issues and challenges : In a 2-3 paragraph paper, list using bullet points, what you believe to be the top 10 issues, challenges, or trends facing leaders today based on what was covered in the videos you watched.
What the total annual inventory costs will be : Hill Inc. produces GPS devices that use a printed circuit board (PCB) obtained from a preferred supplier. The annual demand for the PCB is 16,000 units per year. Demand is relatively constant through the year and the ordering cost is $25 per order. d..
Determine the approximate drag coefficient for the parachute : A 5-m-diameter parachute of a new design is to be used to transport a load from flight altitude to the ground with an average vertical speed of 3 m/s. The total weight of the load and parachute is 200 N. Determine the approximate drag coefficient ..
Define social responsibility : Define social responsibility. What are the similarities and differences between both companies regarding their corporate social responsibility efforts?
Explain the concerns of using stimulant drugs to treat adhd : Attention deficit hyperactivity disorder (ADHD) has received a lot of media coverage in the past ten years. One of the things most misunderstood about the disorder is the treatment. Children (and adults) afflicted with ADHD are often treated with ..
Minimize the total costs while meeting the demands : The Boswell Manufacturing Corporation makes and sells dishwashers. Orders have been received from several retail stores for delivery at the end of each of the next three months: June 195 units demanded, July 215 units demanded, and August 205 units d..
Write a paper incorporating feedback from your instructor : BA500- Write a 2,000-3,000 word paper in APA format incorporating the feedback from your instructor throughout the course using the Business Design outline below.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the ratio db for which a the maximum stress will

a couple m will be applied to a beam of rectangular cross section that is to be sawed from a log of circular cross

  Determine the mechanical efficiency of the pump

Water is being pumped from a large lake to a reservoir 30 m above at a rate of 5x10-3 m3/s by a 12 kW (shaft) pump. If the irreversible head loss of the piping system is 8m, determine the mechanical efficiency of the pump.

  A thermocouple outputs a voltage that is linearyl

a thermocouple outputs a voltage that is linearyl proportional to temperature. it is used to measure an input signal

  What is its book value after five years

She spent the rest of her income personally. At the end of five years, Molly found that her loan was paid off but the equipment was wearing out.

  A flag pole made of solid aluminum is 20 feet tall and one

a flag pole made of solid aluminum is 20 feet tall and one inch in diameter. the pole is situated in full sunlight and

  What is the required mass flow of the extraction steam

A regenerative steam power cycle has a closed feed water heater that heats 20 kg/s of water from 100°C, 20 MPa to 250°C, 20 MPa. The extraction steam from the turbine enters the heater at 4 MPa, 275°C, and leaves as saturated liquid.  What is the req..

  Dring which the pressure-volume relationship is pv

a piston-cylinder assembly contains air initially at 2 bar and 300 k and occupying a volume of 2 m3. the air undergoes

  The system is cooled at constant pressure until it reaches

a cylinder is fitted with a frictionless piston contains 10 lbm of r-134a at 100 psia 300 f. the system is cooled at

  The rate of heat transfer to the air is 350 kjkg neglecting

air enters a device operating at steady state at 18 bar and 572 k and leaves at 1.5 bar and 520 k with a volumetric

  What reduction in co2 generation did the program achieve

Assuming that imported oil cost $55 per barrel, how long did it take for the savings in import to equal the investment in the program?

  Find the velocity with which particle b begins to move if

particle a of mass ma 1.0 kg is at the edge of a table with height 1.0 m. it is connected to a particle b of mass mb

  What force is the drill bit placing on the surface

Suppose a 24V drill has a current drawn from it that measures 5 amps. The drill bit is 2 inches in diameter. What force is the drill bit placing on the surface if the speed is 25 rpm? Assume the drill has an efficiency of 90%

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd