Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Using only resistors, capacitors and op-amps design a circuit meeting the following criteria:The circuit acts as a band pass filter. The 3dB points arer at 100 and 1000 Hz. The mid-range gain is -1 V/V and the mid-band input resistance is on the order of 10 K ohms.assume ideality for any op-amp and negiect any variation in the open loop gain as a function of frequency ,your analysis should begin with the Bode plot experessing the design criteria. Then determine the apporpriate transfer function and then deduce the form of the appropriate circuit.Determine all element values for R and C. simulate your circuit and show that it has the necessary Bode plot.
The transfer function of a circuit is given by H(s)= 2s+4/4s^2+2s+2 a. Express the transfer function in a form in which the coefficients of the highest power of s are unity in both numerator and denominator.
Calculate the maximum power that can be sent through an a=2cm , b=1cm air-filled waveguide at 12 GHz such that dielectric breakdown does not occur. Assume that the dielectric strength of air at atmospheric pressure is 3x10^6 [V/m]
A tank of 0.52 m3 capacity is filled with steam at 2 MPa and 350oC. The tank and its contents are slowly cooled to 125oC. Answer the following questions assuming that there was a negligible volume change during the cooling process
When writing or speaking about reactance, how do we distinguish inductive reactance from capacitive reactance. How are resistances, inductive, and capacitive reactance treated in calculations of AC voltage and current.
Determine the output voltage for an op-amp comparator circuit with a non-inverting input reference voltage of + 2 VDC and an inverting input signal of - 1 VDC. The op amp reaches output saturation voltages of + or -13 V at the limits.
Considering a three phase delta connected synchronous machine, the terminal line-line voltage is 1 p.u, the stator leakage inductance is 0.2 p.u, ignore the stator winding resistance, the rotor wind current is adjusted by a dc voltage source with ..
Assume a binary PCM system in which the system ratio of the bit energy to the one-sided noise density at the receiver input is 10 dB. Assume that the probability of error for any value of the independent variable off the scale can be approximated ..
b- Evaluate the sum of the second row of B. c- Multiply the second column of B and the first column of A. d- Evaluate the maximum value of the vector resulting from element-by-element multiplication of the second column of B with the first column ..
The One river Hydroelectric Project generated power for BPA along the Two River from the early 1800s until 1900, when it was decommissioned due to environmental issues. The maximum flow rate through the system was 25 m3/s, and the hydraulic head w..
A PCM channel consists of 10 links, with a regenerative repeater at the end of each link. If the detection error probabilities of the 15 detectors are p1, p2, ....... , p15, determine the detection error probability of the entire channel if pi
Obtain polar plot using nyquist command. determine the stability of closed loop system based on nyquist criterion. design a compensator to meet the P.O. = 10%. Plot the before and after plot on the same nyquist plot.
A ripple carry adder is made of full adder cells each having 1 unit of combinational delay. To convert a four-bit ripple carry adder into a four stage pipeline adder proceed as following.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd