Determine the angles a and ß

Assignment Help Mechanical Engineering
Reference no: EM131381158

A building's roof has "6 in 12" slope in the front and back and "8 in 12" slope on the sides. Determine the angles α and β that should be used for cutting sheets of plywood so they properly meet along edge AB of the roof

1805_51ac412a-2791-4afc-a904-32c2a1c0be01.png

Reference no: EM131381158

Questions Cloud

What percentage of syrians have left their homes : Geog207- To answer this question thoroughly, you may want to consider the following questions. Why are people leaving Syria? How many people have left? What percentage of Syrians have left their homes?
Test the vice presidents hypothesis : Assume normally distributed populations of occupancy rates with equal population variances. Test the vice president's hypothesis.
Recent study on stress and coping : In a recent study on stress and coping, researchers found that people facing a terrible problem (ex. taking care of a terminally ill family member) were better off if they could take a psychological "time out" by allowing themselves time to enjoy ..
Effectiveness of company leadership : 1. Assess the effectiveness of your company's leadership. 2. Discuss the basis of your company's competitive advantage and the potential challenges to its strategy.
Determine the angles a and ß : A building's roof has "6 in 12" slope in the front and back and "8 in 12" slope on the sides. Determine the angles α and β that should be used for cutting sheets of plywood so they properly meet along edge AB of the roof
Describe the physical and cognitive issues involved in aging : Describe stereotypes about the elderly that are prevalent in society, and how those stereotypes affect your personal beliefs concerning the elderly.Describe the physical and cognitive issues involved in aging.Discuss the mental health treatment is..
What is the role of information technology in organizations : What is the role of Information Technology in organizations and businesses? How do IT managers interact with others in the organization
Determining the characteristics for attributes : Characteristics for attributes are also called properties. So every entity must have attributes to help make it unique. Behavior is important because the entity responds to other entities.
Cost-effectiveness analysis : Reflect on Reinhardt's 2009 article, "'Cost-Effectiveness Analysis' and U.S. Health Care." The article describes different approaches to analyzing health care. In 5-7 pages, do the following:

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd