Determine the amount of steam generated per unit of fuel

Assignment Help Mechanical Engineering
Reference no: EM13623894

A steam boiler heats liquid water at 200 ºC to superheated steam at 4 MPa and 400 ºC. Coal fuel from Utah which has an ultimate analysis (by mass) as 61.40 percent C, 5.79 percent H2, 25.31 percent O2, 1.09 percent N2, 1.41 percent S, and 5.00 percentash (non-combustibles) is burned steadily with 50 percent excess air. The fuel and air enter the boiler at 25 ºC and the products of combustion leave at 227 ºC. Determine the amount of steam generated per unit of fuel mass burned, the change in the exergy of the combustion streams, in kJ/kg fuel and the steam stream, in kJ/kg steam, and the lost work potential, in kJ/kg fuel. Neglect the effect of the sulfur in the energy and entropy balances.

Reference no: EM13623894

Questions Cloud

Determine the value of x what might you do if you failed to : a potentiometer circuit for comparison of two resistances. the balance point with a standard resistor r 10.0nbspomega
The free convection heat transfer coefficient on a thin hot : the free convection heat transfer coefficient on a thin hot vertical plate suspended in still air can be determined
A secondary cell after long use has an emf of 19 v and a : a six lead-acid type of secondary cells each of emf 2.0 v and internal resistance 0.015nbspomega are joined in series
A pressure gage reading is 20 mm deltahg if the gage is : a pressure gage reading is 20 mm deltahg. if the gage is located at an elevation of 2000m.what is the absolute
Determine the amount of steam generated per unit of fuel : a steam boiler heats liquid water at 200 ordmc to superheated steam at 4 mpa and 400 ordmc. coal fuel from utah which
A 001 significance level is used for a hypothesis test of : a 0.01 significance level is used for a hypothesis test of the claim that when parents use a particular method of
Try to recall a decision you made today discuss how you : try to recall a decision you made today. discuss how you made the decision. now follow the steps of the scientific
In a potentiometer arrangement a cell of emf 125 v gives a : in a potentiometer arrangement a cell of emf 1.25 v gives a balance point at 35.0 cm length of the wire. if the cell is
If the seat pocket diameter in a ball valve is 5000 the : if the seat pocket diameter in a ball valve is 5.000 the seat seal ring to ball sealing diameter is 4.438 and the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Assuming that the bypassed air produces no thrust and

a jet engine is a serial combination of a compressor an adiabatic constant pressure combustor and a turbine in that

  Find the safe applied torque that can be transmitted

Find the safe applied torque that can be transmitted by the shaft ABCD, if the maximum shear stress in the hollow section is 47 MPa and G = 82.5 GPa.

  How high above the ground is the balloon at the instant the

the position of an object is moving along an x axis is given by x3t - 4t2t3 where x is in meters and t is in

  The ball is in contact with the racket for 325 if the

a tennis racket hits a tennis ball with a force of where 1230 500 and is the time in milliseconds. the ball is in

  Determine the work done during the process a by plotting

gas with an initial volume of 0.36 m3 is slowly compressed to a final volume of 0.16 m3 by a process during which the

  Plastics and other polymeric materials are expensive with

plastics and other polymeric materials are expensive with respect to steel and are usually more costly than aluminum

  Determine the cycle thermal efficiency for the internally

an air standard brayton closed cycle receives air at 1 atm and 298 k. the upper temperature and pressure limits are 5

  An industrial water shutoff valve is designed to operate

an industrial water shutoff valve is designed to operate with 30lbs of force and will encounter 200lbs of resistance

  The u velocity component of a steady two dimensional

the u velocity component of a steady two dimensional incompressible flow field is u 4x 3y 1. velocity component v is

  What is the percent span for the old and new set points

In order to increase production rate a reactor set point was increased from 160 psig to190 psig. The reactor pressure transmitter was recalibrated from 0-200 psig to 0-300 psig.

  If the velocity out the 2-cm-diameter tube is 15 ms

water flows into a volume that contains a sponge with a flow rate of 0.02 m3s. it exits the volume through two tubes

  A vapor in a cylinder is compressed frictionlessly from 20

a vapor in a cylinder is compressed frictionlessly from 20 to 60 psia in such a manner that pvconstant. the initial

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd