Determine the amount of nitrogen gas that has escaped

Assignment Help Electrical Engineering
Reference no: EM13259012

A 20-m3 tank contains nitrogen at 23 C and 600 kPa. Some nitrogen is allowed to escape until the pressure drops to 400 kPa and the temperature to 20 C. Determine the amount of nitrogen gas that has escaped in kg. How much in this in Kmoles?

Reference no: EM13259012

Reviews

Write a Review

 

Electrical Engineering Questions & Answers

  Why single interrupt is interpreted as multiple interrupts

Assume that the I bit for external hardware interrupt IRQ is enabled and is low-level triggered. Explain how this interrupt works when it is activated. How can we make sure that a single interrupt is not interpreted as multiple interrupts

  Which false negatives are significantly more serious

False positive and false negative rates can be adjusted, and they are often complementary: Lowering one raises the other. List two situations in which false negatives are significantly more serious than false positives.

  What is the minimum bandwidth necessary on transmission line

A transmitter is using a 2B1Q and operating at 3 Mbps. What is the minimum bandwidth necessary on the transmission line for successful communication

  What is the direction of the friction force on the upper box

You are lowering two boxes, one on top of the other, down the ramp shown in the figure by pulling on a rope parallel to the surface of the ramp. Both boxes move together at a constant speed of 16cm/s.

  Determine the depletion scr layer width w

An ideal abrupt silicon pn junction has a  \(N_{A} = 2 x 10^{17} cm^{-3} , N_{D} = 2 x 10^{15} cm^{-3} , \) 1) With derivation steps, calculate internal potential barrier V0 at 300K and 400K, respectively

  Find the line-to-line voltage of the line at the sending end

A balanceed three-phase load of 15 MA with a lagging load factor of 0.85 is supplied by a 115KV subtransmission line. if the line impedance is 50+j100Ohm per phase, determine the following: (a) The line current of the load.

  Determine the charge and current flowing in the circuit

The capacitor in an RC circuit (R=10.0k Ohms and C=25.0uF) is initially uncharged. Determine the charge and current flowing in the circuit at 0.40 time constants (t=0.40 tau) after the circuit is connected to a 9.00 V battery.

  Find speed of an electron beam coming from an electron gun

The axis of the cylinder is along the z axis, and the electrons are moving with a velocity vector v in the positive z direction. The velocity of the electrons is 0.1c where c is the speed of light (2.99792458 ´ 108 [m/s]). The magnitude of the cur..

  Describe performance differences between an am and fm system

Describe the performance differences between an AM and FM system. Be sure toinclude parameters suchas: Power efficiency, spectral efficiency,noise immunity,and performance.

  Calculate the armature voltage to be applied in steady state

Plot the steady state torque-speed characteristic for Va = 100V, 60V, and 30V. Calculate the armature voltage to be applied in the steady state at the speed of 1500 rpm when the motor torque load require is 3 Nm.

  Determine the standing wave pattern for the voltage

Determine the standing wave pattern for the voltage in the line. Express the result in real insantaneous form and simplify

  Write assembly language to add two 32-bit packed bcd numbers

write a subroutine in 68000 assembly language to add two 32-bit packed BCD numbers. BCD number 1 is stored at a location starting from $ 500000 through $ 500003, with the least significant digit at $ 500003 and the most significant digit.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd