Determine the amount of money this facility will save a

Assignment Help Mechanical Engineering
Reference no: EM13640219

During a plant visit, it was noticed that a 12-m-long section of a 12-cm-diameter steam pipe is completely exposed to the ambient air. The temperature measurements indicate that the average temperature of the outer surface of the steam pipe is 75°C when the ambient temperature is 5°C. There are also light winds in the area at 25 km/h. The emissivity of the outer surface of the pipe is 0.8, and the average temperature of the surfaces surrounding the pipe, including the sky, is estimated to be 0°C. Determine the amount of heat lost from the steam during a 10-h-long work day.

Steam is supplied by a gas-fired steam generator that has an efficiency of 80 percent, and the plant pays $1.05/therm of natural gas (1 therm = 105,500 kJ). If the pipe is insulated and 90 percent of the heat loss is saved, determine the amount of money this facility will save a year as a result of insulating the steam pipes. Assume the plant operates every day of the year for 10 h. State your assumptions.

Reference no: EM13640219

Questions Cloud

A ball thrown straight upward returns to its original level : a ball thrown straight upward returns to its original level in 2.60 s. a second ball is thrown at an angle of 32.0deg
A study is run to estimate the association between exposure : a study is run to estimate the association between exposure to lead paint in childhood and attention-deficit
A potential difference of 120 v is applied to the capacitor : a spherical capacitor is formed from two concentric spherical conducting shells separated by vacuum. the inner sphere
Calculate the total amount in the two funds at the end of 2 : you are given1 fund x accumulates at an interest rate of 8 compounded quarterly2 fund y accumulates at an interest rate
Determine the amount of money this facility will save a : during a plant visit it was noticed that a 12-m-long section of a 12-cm-diameter steam pipe is completely exposed to
How does this information relate to the fact that : cyclopropane has significantly less angle strain than cyclopropane yet is only slightly lower in energy. how can this
Two parallel plates have charges of 600 x 10-4c and -600 x : two parallel plates have charges of 6.00 x 10-4c and -6.00 x 10-4c respectively.a. what is the electric field between
Suppose that a stray neutron with an initial speed of 23 : suppose that a stray neutron with an initial speed of 2.3 times 107 ms is just barely captured by a nucleus with
Determine the axial force and deformation of the diameter : a cylindrical bar of radius 15 mm and length 100 mm is held at both ends. if at 30degc no axial force exists in the bar

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd