Determine the ambient temperature in the oven if the steel

Assignment Help Mechanical Engineering
Reference no: EM13638484

prings in a suspension system of automobiles are made of steel rods heated and wound into coils while ductile.Consider steel rods (ρ= 7832kg/m3, cp= 434 J/kg K, and k = 63.9 W/m K) with diameter of 2.5cm and length of 1.27m. The steel rods are heated in an oven with a uniform convection heat transfer coefficient of 20 W/m2K. The steel rods were heated from an initial temperature of 20 C to the desired temperature of 450 C before being wound into coils. Determine the ambient temperature in the oven, if the steel rods were to be heated to the desired temperature within 10 minutes.

Reference no: EM13638484

Questions Cloud

Two forces 473 n at 11 degrees and 423 n at 28 degrees are : two forces 473 n at 11 degrees and 423 n at 28 degrees are applied to a car in an effort to accelerate it.a what is the
If a number of the hot air balloons started from the same : a hot air balloon travels with the wind. the wind velocity is v6i 10j ms for the first hour and then it is 10i 5j ms
Gasohol is a mixture of 90 gasoline and 10 ethanolch3 ch2 : gasohol is a mixture of 90 gasoline and 10 ethanolch3 ch2 oh. ethanol is considered anenviornmentally friendly fuel
How does the position vs time graph differ from a position : how does the position vs time graph differ from a position vs time graph for constant velocity motion? how does it show
Determine the ambient temperature in the oven if the steel : prings in a suspension system of automobiles are made of steel rods heated and wound into coils while ductile.consider
A small block of mass m is given an initial speed vo up a : a small block of mass m is given an initial speed vo up a ramp inclined at angle theta to the horizontal. it travels a
The tube wall temperature is maintained at 290 k if the : saturated r-134a at 310 k flows through a 30-mm-diameter .8-m-long tube. the tube wall temperature is maintained at 290
Calculate kf for cdnh342 from the following data a mixture : calculate kf for cdnh342 from the following data a mixture of 10.0 ml of 0.120 m cdno32 with 40.0 ml of 0.600 m nh3
A what minimum constant acceleration does the aircraft : a cessna aircraft has a lift-off speed of 120 kmh.a what minimum constant acceleration does the aircraft require if the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the final velocity of each car after all impacts

at an amusement park there are 200-kg bumper cars a b and c that have riders with masses of 40 kg 60 kg and 35 kg

  I the mass is deflected 2cm down measured from its

the ratio km of a spring-mass system is given as 4. if the mass is deflected 2cm down measured from its equilibrium

  Air at 35degc 105 kpa flows in a 100 mm times 150 mm

air at 35degc 105 kpa flows in a 100 mm times 150 mm rectangular duct in a heating system. the volumetric flow rate is

  The concentration of hydrogen on the other side of the

a thin 1 mm thick ?-iron membrane at 250degc is subjected to an atmosphere of hydrogen gas on one side and the

  Heat transfer between the compressor and its surroundings

refrigerant 134a enters a compressor operating at steady state as saturated vapor at -4 degc and exits at a pressure of

  Consider the incompressible-flow field u ax by v cx dy

consider the incompressible-flow field u ax by v cx dy w 0. for what conditions on constants a b c d is this flow

  A 15-tooth pinion having a pressure angle of 25ordm and

a 15-tooth pinion having a pressure angle of 25ordm and module of 8mm is to drive an 18-tooth gear. determine for both

  Hw much heat is needed to a 03m3 rigid volume containing

how much heat is needed to a 0.3m3 rigid volume containing saturated water vapor at 1000 kpa in order for final

  As the hollow steel g 77 gpa shaft shown rotates at 180

as the hollow steel g 77 gpa shaft shown rotates at 180 rpm a stroboscopic measurement indicates that the angle of

  Determine the stresses acting on an element inclined at 45

a material element experiences 50 mpa compression in the x-direction 10 mpa tension in the y-direction and a negative

  Determine the acceleration a of the car just after passing

a car is climbing the hill of slope theta1 at a constant speed v. if the slope decreases abruptly to theta2 at point a

  Discuss the effects of grinding and turning on the

discuss the effects of grinding and turning on the endurance limit of steel. what is the reason of change in fatigue

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd