User Account

All Pages

Determine the absolute pressure of the water at the ground

Assignment Help Mechanical Engineering
Reference no: EM13612633

The water level in a sealed tank is 26 m above the ground. The pressure in the air space above the water is 0.25 MPa gage. The average density of the water is 1000 kg/m3. Determine the absolute pressure of the water at the ground level. Atmospheric pressure is 101.325 kPa. Acceleration due to gravity is 9.81 m/s2.

Reference no: EM13612633

Questions Cloud

A random variable x has the following probability : a random variable x has the following probability distrubution.x fx0 0.081 0.172 0.453 0.254 0.05a. deterime the
Determine the power needed to drive the pump if the pump : a feed water pump operates with a flow rate of 350 kgs. the water enters at 420 k. the inlet pressure is 0.7 mpa and
Estimate the mean and standard deviation of this process : components used in a cellular telephone are manufactured with nominal dimension of .3 mm and lower and upper
You are visiting las vegas and would like to come home with : you are visiting las vegas and would like to come home with more money than you arrived with. use your knowledge of
Determine the absolute pressure of the water at the ground : the water level in a sealed tank is 26 m above the ground. the pressure in the air space above the water is 0.25 mpa
The gap between the two plates is h 0005 m the fluid has a : there is flow between two plates as shown in the schematic. the bottom plate is stationary. the top plate is moving at
Hydrogen at 25 bar 450degc enters an adiabatic turbine and : hydrogen at 25 bar 450degc enters an adiabatic turbine and expands to 2 bar 160degc with a mass flow rate of 0.2 kgs.
Determine a the temperature of the refrigerant exiting the : refrigerant 134a at -10degc 1.4 bar and a mass flow rate of 280 kghr enters an insulated compressor operating at steady
This member is to be designed according to maximum shear : a solid square cross-sectional bar bxb with a yield stress of 250 mpa is subjected to a compressive axial force p 140

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Helium gas in an ideal otto cycle is compressed from 12degc

helium gas in an ideal otto cycle is compressed from 12degc and 2 l to 0.25 l and its temperature increases by an

  Assuming the center-to-center distance of two atoms not

under a stress of 1105 mpa a sample of ag has a modulus of elasticity of 580 gpa. assuming the center-to-center

  What is the nozzle-exit-to-throat area ratio

What is the nozzle-exit-to-throat area ratio for case (a)? The gross thrust is the contribution to engine thrust made by the exhaust nozzle only.

  Brayton gas turbine cycle has two stages of compression

A Brayton gas turbine cycle has two stages of compression and two stages of expansion. The pressure ratio across each stage of the compressor and turbine is 3. The air enters each stage of  the compressor at 300K and each stage of the turbine at 1..

  Approximate location of the laminar turbulent transition

Find the approximate location of the laminar turbulent transition - what is the net heat removed by the air around the rod?

  Why is correct tightening of friction grip bolts important

why is the correct tightening of friction grip bolts important?

  The valve is next opened and steam from the line at 135 mpa

a tank has a volume of 0.35m3 and initially contains saturated vapor at 333 kpa. the valve is next opened and steam

  If a pound of coal produces 183 pounds of co2 during the

a hot water leak in one of the facets of your apartment can be very wasteful. a continuous leak of one quart per hour a

  What is the velocity and rate of flow of the metal

What is the velocity and rate of flow of the metal into the mold? Is the flow turbulent or laminar? (Pure aluminum density ρ = 2.7 g/cm3).

  Estimate the infiltration flow rate

Estimate the infiltration flow rate if the window is partially open (assuming the window open area is 2 meter squared).

  What magnetic field should be applied to trap electrons

In a DC planar magnetron sputtering system at 1000 V, the cathodeanode spacing is 10 cm. What magnetic field should be applied to trap electrons within 0.5 cm of the target?

  Determine the power

A commercial heat pump has energy in to the system at a rate of 60 kW from a thermal reservoir. If the power input from an electric motor is 15 kW, (a) determine the power (kW) delivered to the office area. (b) Determine the coefficient of perform..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd