Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A symmetrical short circuit is suddenly applied to a synchronous generator on open circuit, terminal voltage 1.0 p.u. The initial peak values of the oscillogram of the short circuit current during the sub-transient, transient and steady state periods are 8.0 p.u., 5.7 p.u. and 1.8 p.u. respectively.
a. Neglecting resistance, determine the synchronous, transient and sub-transient reactances.
b.If the machine is delivering 1.0 p.u. current at 0.8 power factor lagging at the rated terminal voltage when the short circuit is applied, calculate the new sub-transient, transient and steady state currents.
What is the impedance of a resistor R in parallel with a series combination of a capacitor C and an inductor L? Assume angular frequency omega(w).
Consider an LTI system with impusle response h(t) = e^(-.2t)*(u(t-1)-u(tt-8)) a) plot h(t - tau) for various values, make sure you show how the parameter t influences the position of the curve in the graph. b)Find the output y when the input is x(t) ..
If the capacitor in the previous problem has a plate separation of 1 mm, what is the average displacement current, to the nearest tenth of a microamp, during that time period Assume a resistance of 180006 ohms and an applied voltage of 14 volts.
A truncated cone has a height of 50cm. The circular faces on the top and bottom have radii of 20 mm and 1mm, respectively. If the material from which the solid cone is constructed has a conductivity sigma of 2 x 10^6 S/m.
The bandwidth of a series resonant circuit is 400 Hz. (a) If the resonant frequency is 4000 Hz, find Q. (b) If R = 10 ohm, what is the value of XL at resonance
A balanceed three-phase load of 15 MA with a lagging load factor of 0.85 is supplied by a 115KV subtransmission line. if the line impedance is 50+j100Ohm per phase, determine the following: (a) The line current of the load
(a) Design a simple PNP current source to give an output current of IO = 0.5 mA (nominal value). The transistor parameters are f = 50, VEE = 10 V, VCC = 10V, |VBE| = 0.7 V, |VCEsat| = 0.3 V and VA = 50 V (for all transistors)
Design an elevator controller for a simple two-floor elevator. On the 1st floor, there is only an up button, and on the 2nd floor, there is only a down button. Within the elevator, there are two buttons: door open and door close.
A 3-D cubic unit cell contains four atoms whose centers are positional halfway up along each of the vertical cell edges and one atom each centered in the middle of the top and bottom faces.
The steady-state electron distribution in silicon can be approximated by a linear function of x. The maximum electron concentration occurs at x = 0 and is n(0) = 2.0 x 1016cm-3. At x = 0.012cm, the electron concentration is 5.0 x 1015cm-3.
Each of the capacitance units is built of 4 similar 100V capacitors. Determine the capacitance of each capacitor.
A 3-D printer lays down a semicircular arc of positively charged plastic with a radiusR = 3.5 cm, and a linear charge density of Lambda = +1.9 uC/m. After the printer has finished the arc, the stylus moves to the center of the arc.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd