Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Assume that the memory locations M[$20], M[$21] and M[$22]. Write a 68HC11 assembly language program (with lots of comments) that will determine the sum of the largest two numbers and store its value in M[$23].
Example: If memory locations contain the following:
M[$20] = $10
M[$21] = $FF
M[$22] = $20
Then your program should write the following in memory:
M[$23] = $30 ; the largest sum is M[$20] + M[$22] = $30
Your program should work for any numbers that are stored in M[$20], M[$21], and M[$23].
HALF-ADDER: S = XY' + X'Y , C = XY (These are the outputs) 1. From the equation given for half-adder, develop an equation for which the half-adder can be constructed just with NAND gates. Draw the circuit as per the equation obtained.
Three loads are connected in parrallel across a 250 Vrms line. Load 1 absorbs 16 kW and 18 kVAR. Load 2 absorbs 10 kVA with a power factor of 0.6 leading. Load 3 absorbs 8 kW with a power factor of 1.
Build a C++ code for vehicle sensing device. Code is required to embed in the device so that then it must sense the location where the vehicle is currently present. The device must be able to track the location of the vehicle for its owner
A calibrated RTD with ALPHA = 0.0041/°C, R = 306.5 Ohms at 20°C, and PD = 30 mW/°C will be used to measure a critical reaction temperature. Temperature must be measured between 50° and 100°C with a resolution of at least 0.1°C.
A saturated npn transistor has a base to emitter applied voltage of 0.6V. The collector to emitter voltage is 0.2V. The collector current is 12mA
Design an adder that computes the sum of four 8-bit numbers, using 8-bit carryripple adders. Use a basic 8-bit carry-ripple adder as a building block for the design.
single phase motor draws 20A from a 200V, 50Hz supply with a lagging power factor of 0.8. Calculate the value of the capacitance needed to bring the current in phase with the voltage.
our senior design team is designing a force sensor to measure a force signal and analyze the signal with a microcomputer (binary system). The analog force signal is between 10 N and 70 N and has the frequency bandwidth of DC - 1000 Hz.
A ball is thrown vertically upwards from a point 1.5 m above the ground, with an initial velocity of 30 m/s. In this problem, neglect the effects of air on the motion of theball, and take g = 10 m/s2. what is the total distance moved by the ball
1.)An op amp requires the design equation Vout = 5Vin & 2Vref + AgVg. What is the value of Ag 2.)The voltage dropout of a voltage regulator is 1.6 V. If a 16 V output is required, what is the minimum regulator input voltage
A linear CW product detector local oscillator has a 500 Hz error while detecting an AM signal. What will the receiver's output sound like What if the receiver is listening to a DSB or SSB signal
2) Draw the logic circuit for each of the following. For each gate, determine EVEN or ODD parity and find the output for the given input data: a) 4-input XOR, input data=1001 b) 5-input XOR, input data-10010 c) 6-input XOR, input data=101001 d) 7-..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd