Determine speed and line current when motor develops torque

Assignment Help Electrical Engineering
Reference no: EM13286283

A 220V dc shunt motor draws 10A at 1800rpm. The armature circuit resistance is .2ohm and the field winding resistance is 440 ohm.what is the torque developed by the motor?
If the field current is unchanged, determine the speed and the line current when the motor develops a torque of 20N-m?

Reference no: EM13286283

Questions Cloud

Define what is the kinetic energy of the emitted electrons : What is the kinetic energy of the emitted electrons when cesium is exposed to UV rays of frequency 1.4x10^15Hz
Find the required relationships between r-l and c : Combine the impedances and find phasor current in the two circuits by using Phasor Ohm ( I= V/Z), then find voltage across each element (eg: VR = I * ZR ). Setting magnitudes equal is the same as setting the square of the magnitudes equal.
Find the ropes angle from the vertical : A 11.1-kg object hangs in equilibrium at the end of a rope (taken as massless) while a wind pushes the object with a 60.3-N horizontal force. find the rope\'s angle from the vertical
Explain gas diffuse faster : Gas A has a density of 0.20 g L, and gas B has a density of 0.80gL, both at the same specific temperature and prassure. Which gas diffuse faster
Determine speed and line current when motor develops torque : A 220V dc shunt motor draws 10A at 1800rpm. The armature circuit resistance is .2ohm and the field winding resistance is 440 ohm.what is the torque developed by the motor
State the mass of carbon dioxide is produced by the complete : What mass of carbon dioxide is produced by the complete combustion of 5.50 grams of hexane, C6H14
What is the capacitance of the two wires : A capacitor is consists of two short sections of parallel wires in air. One wire is found to be of the voltage of 58 V, What is the capacitance of the two wires
What is the cost of equity from retained earnings : Scanlon Inc.'s CFO hired you as a consultant to help her estimate the cost of capital. You have been provided with the following data: rRF = 4.10%; RPM = 5.25%; and b = 1.30. Based on the CAPM approach, what is the cost of equity from retained ear..
How far was the train from the cow : Amtrak's 20th-Century Limited is en route from Chicago to New York at 120km/h, How far was the train from the cow when the engineer first applied the brakes

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is the frequency resolution-df for the analysis

An engineer decides to take 600 samples at sampling frequency 9000Hz. A Fast Fourier Transform (fft) program was applied to obtain the frequency spectrum of the signal. What is the frequency resolution,df, for the analysis

  Why the circuit must have a high input impedance

I)Design a circuit that gives you the following relation between input and output Vout = 2.17Vin + 5 Here are the constraints you need to work with: 1) Only one power supply that gives ±12V is available 2) Available op-amps run on ±12V

  Explain fundamental periods versus discrete time

A signal x[n] is formed by sampling a signal x(t) = -4sin(200*pi*t) at a sampling rate of 400Hz. Graph x[n] over 10 fundamental periods versus discrete time. Then do the same for the sampling frequencies of 60 and 200Hz.

  Develop pseudo-code below for program to retrieve two bytes

Develop the pseudo-code below for a program that will retrieve 2 bytes (NUM1 and NUM2) from memory, determine which is closest to the numeric value 50, and indicate the result by setting a variable named "CLOSEST" to 1 (if 1st byte is closest) or ..

  Determine the average power dissipated in re in watts

For the circuit following parameters are given with Vcc = 18 volts DC: Rs = 0 ohm r pi = 1000 ohm Rb = 1750 ohms C1 = 10 microfarads gm = 50mS RL = 100 ohms Ce = 0.1 microfarads Re = 135 ohms C2 may be considered very large

  What is the magnitude of the induced emf per phase in rotor

A three-phase induction motor operates at a slip of 3% and has a rotor copper loss of 300W. The rotational loss is 1500W. Determine (a) The air-gap power (b) The power output (c) If the rotor impedance is 0.2+j0.8 ohm/phase,

  What is the electric field e in all regions of space

A charge density of ohm Coulombs per square meter is uniformly distributed over a thin and very long cylindrical shell of radius a. You want to know the electric flux density field D and the electric field E generated by this charge at all points ..

  What must be the distance be between filaments 2 and 3

Filament 1 is on the left, filament 2 is in the middle, and filament 3 is on the right. Filaments 1 and 2 have currents of 1 A in the ba z direction, and filament 3 has a current of 2 A in the ba z direction

  Find q1 such that the force on a test charge given

Point charges Q1 and Q2 are respectively located at (4,0,-3) and (2,0,1). If Q2 = 4 nC, find Q1 such that (a) The E at (5,0,6) has no z-component (b) The force on a test charge at (5,0,6) has no x-component.

  Discuss the advantages of transforming time-domain circuits

Discuss why phasor analysis can only be performed on single-frequency circuits. For multiple frequencies what type of analysis must be performed Discuss the advantages of transforming time-domain circuits into the corresponding frequency domain.

  Calculate the normal strain and elongation of the plate

A square plate of titanium is 12cm along the top, 12cm on the right side, and 5mm thick. A normal tensile force of 15kN is applied to the top side of the plate. A normal tensile force of 20kN is applied to the right side of the plate.

  Write a function that takes inputs of yards and feet

There are 5280 feet per mile. There are 3 feet in a yard. Use appropriate parameter passing and return mechanisms. Use appropriate datatypes. For example, with inputs of 1760 yards and 1320 ft, the result would be 1.25 miles.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd