User Account

All Pages

Determine reaction on the cross head guides

Assignment Help Mechanical Engineering
Reference no: EM13963865

The lengths of crank and connecting rod of a horizontal engine are 300 mm and 1.2 m respectively. When the crank has moved 300 from the inner dead centre, the acceleration of the piston is 35m/s2.

The average frictional resistance to the motion of the piston is equivalent to a force of 550N and net effective steam pressure on piston is 500kN/m2 .

The diameter of the piston is 0.3 m and mass of reciprocating parts is 160 kg. Determine (i) Reaction on the cross head guides (ii) Thrust on the crank shaft bearings and (iii) Torque on the crank shaft

Reference no: EM13963865

Questions Cloud

Difference in the individuals driving : Assuming that the difference of each pair is coming from an approximately normal distribu- tion, test if there is any difference in the individuals' driving ability under the two conditions. Use α = 0.05.
Find the mass of the flywheel : The total fluctuation of speed is not to exceed ± 1.8% of the mean speed. If the radius of gyration of flywheel is 0.7m, find the mass of the flywheel.
Find the frequencies of the first three harmonics : A tuning fork is sounded above a (narrow) resonating tube as in lab. The first resonant situation occurs when the water level is 0.08 m from the top of the tube, and the second when the level is at 0.24 m from the top. Let vsound = 340 m/s.
Representing the time between successive arrivals : Let X be a random variable representing the time between successive arrivals at a checkout counter in a supermarket. The values of X in minutes (rounded to the nearest minute) are
Determine reaction on the cross head guides : Determine Reaction on the cross head guides, Thrust on the crank shaft bearings and (iii) Torque on the crank shaft
Unknown probability p of heads : Let X1,..., Xn be a random sample recorded as heads or tails resulting from tossing a coin n times with unknown probability p of heads. Find the MLE pˆ of p. Also using the invariance property, obtain an MLE for q = 1 - p. How would you use the re..
Geometric distribution-probability of success : Let X1,..., Xn be a random sample of size n from the geometric distribution for which p is the probability of success. (a) Use the method of moments to ?nd a point estimator for p.
Determine the net load on the gudgeon pin : The gas pressure on the piston is 6 kg/cm2 when it has moved 1.5 cm from the inner dead centre on its power stroke - Determine the net load on the gudgeon pin when the engine runs at 2000 rpm . At what speed this load will be zero ?
Calculate the entropy of a mole of oxygen : Calculate the chemical potential of oxygen in earth's atmosphere near sea level, at room temperature. Express the answer in electron-volts.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Object depends on the dimensionless drag coefficient

The drag force on an object depends on the dimensionless drag coefficient, the density of air, the object velocity, and the frontal area of the object. By only considering units obtain a relation for the drag force.

  Analytical method base on force decomposition

The lever BCD is hinged at C and attached to a control rod at B. If P = 100 lb, determine the tension in rod AB and the reaction at C, using both the graphical method and the analytical method base on force decomposition.

  There are 4 octahedral sites and 8 tetrahedral sites in

there are 4 octahedral sites and 8 tetrahedral sites in the fcc unit cell stated on slide 17-7 and feo has the nacl

  Obtain a general relation for temperature distribution

consider a water pipe of length l17m inner radius r115cm outer radius r220cm and thermal conductivity k14wmk. heat is

  A six-station automatic assembly line has an ideal cycle

a six-station automatic assembly line has an ideal cycle time of 12 sec. downtime occurs for two reasons. first

  Suppose that water at room temperature of 27degc is put

suppose that water at room temperature of 27degc is put into an ideal refrigerator that maintains an inside temperature

  Calculate the pressure of methane gas

Calculate the pressure of 15.0g of methane gas in a 1.50L vessel at 45.0 degrees C using (a) the Ideal Gas Law and (b) the van der Walls equation using the following information about the constants, a and b: a = 2.253 and b = 0.04278.

  Determine the power the heat pump

If the COP of the heat pump is 2.8, determine the power the heat pump draws when running.

  Determine the time required by a diesel-electric locomotive

Determine the time required by a diesel-electric locomotive, which produces a constant drawbar pull of 60,000 lb, to increase the speed of an 1800 ton freight train from 20 mi/hr to 30 mi/hr up to 1-percent grade. Train resistance is 10 lb per ton.

  When operated at 2600 rpm this engine produces 98 hp

a 6-cylinder 3.8 l spark ignition engine operating on the ideal otto cycle takes in air at 104 kpa and 20 degrees

  Consider a steam turbine where steam enters with a

consider a steam turbine where steam enters with a pressure of 10 mpa and temperature 500 degc and expands

  If the initial temperature of the pin is 800 degrees c

a molybendenum metal pin is 25 mm long and 2mm in diameter. the air surrounding the pin is 200 degrees c the walls of

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd